|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
07-13-2022, 12:08 PM | #1 |
Senior Member
Join Date: May 2010
Location: Bridgehampton, NY
Posts: 125
|
Radiator hoses for 1935 ford
Can anyone recommend a source for radiator hoses for a 1935 Ford. I have tried many of the usual sources an all seem to be out of stock. Any help would be appreciated.
Thanks in advance. |
07-13-2022, 01:27 PM | #2 |
Senior Member
Join Date: May 2010
Location: Above the gnat line in Georgia
Posts: 7,009
|
Re: Radiator hoses for 1935 ford
Do you have a stock engine? Someone is making a hose for the 35-36 with a later engine with the hose connection in the center of the head.
__________________
Life is like a roll of toilet paper. The closer to the end, the faster it goes. It is better to be seen, than viewed. "We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm". |
Sponsored Links (Register now to hide all advertisements) |
|
07-13-2022, 01:49 PM | #3 |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 9,016
|
Re: Radiator hoses for 1935 ford
Jack, Napa sells straight radiator hose by the foot. Just figure out the inside diameter(s) and total length you require.
__________________
"I can explain it for you. However, I can't understand it for you". |
07-13-2022, 05:53 PM | #4 |
Senior Member
Join Date: Sep 2020
Location: Mount Desert, Maine
Posts: 504
|
Re: Radiator hoses for 1935 ford
I purchased a set of red line hoses for my ‘36 Phaeton from Joes - good fit, although lower hoses elicited the usual profanity trying to bend the unbendable into a too small space. Note that upper hoses went in without modification while both lower hoses required trimming prior to application of profanity.
__________________
No job’s done ‘til it’s all done |
07-13-2022, 06:59 PM | #5 | |
Senior Member
Join Date: Jul 2011
Location: SF Bay Area
Posts: 6,648
|
Re: Radiator hoses for 1935 ford
Quote:
Jacques, Next time that job comes up, simply disconnect the front motor mounts and lift the engine sufficiently to angle a hose onto the inlet/outlet. Then as you lower the engine, that hose knows where it's going. Do one hose at a time, orient the clamps to convenient positions, and while you're at it, replace your mushy old motor mounts.
__________________
Alan |
|
07-13-2022, 07:43 PM | #6 | |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,115
|
Re: Radiator hoses for 1935 ford
Sponsored Links (Register now to hide all advertisements)
Quote:
Nahh! That's way TOO easy! Coop . |
|
07-13-2022, 07:46 PM | #7 |
Member
Join Date: Feb 2013
Location: Rancho Cordova, Ca.
Posts: 56
|
Re: Radiator hoses for 1935 ford
These are the only sets we have in at the moment
#05729 RADIATOR HOSE SET- FORD SCRIPT - RED STRIPE 1932-36 4 HOSES - 8 CLAMPS FOR STOCK FLATHEAD ENGINE LIMITED STOCK https://www.vintageford.com/part_sea...5729&Category= |
07-13-2022, 11:53 PM | #8 |
Senior Member
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,578
|
Re: Radiator hoses for 1935 ford
I like to use " sil glyde" on hose installations, slides on easy and comes off without a fight years later. Napa brand name, I suppose there are others similar
|
07-13-2022, 11:58 PM | #9 |
Senior Member
Join Date: Jul 2011
Location: SF Bay Area
Posts: 6,648
|
Re: Radiator hoses for 1935 ford
From that name, it sounds like silicone, and there isn’t anything better for rubber.
__________________
Alan |
|
|
Sponsored Links (Register now to hide all advertisements) |
|