|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
09-30-2013, 11:03 PM | #1 |
Senior Member
Join Date: May 2010
Location: Oakdale,Ca
Posts: 1,323
|
Well, a first for me...
I've probably made 200+ double flares, from brake lines, fuel lines, hydraulic's, etc...I know exactly why there is a small recess in a tubing cutter...for when we forget to put the fitting on!
Now as I said...this is a first for me...sure, I've goofed up, put one fitting on backwards...forgot to put a fitting on, put the fitting on below the bend...etc...all required cutting the tubing, and reflaring...we've all (if you do it yourself) been there. But today I had a "first"...while making up brake lines for my pickup...I got the tube set into the fitting in the WC...bent it, formed it, etc...marked it for the correct cut...very nice "custom" fit...would have rivaled Henry's... Took the line down...cut and reamed it, then proceeded to flare BOTH ends...with no fittings! So, I'm 51...does it get worse later on? |
09-30-2013, 11:35 PM | #2 |
Senior Member
Join Date: Nov 2010
Location: NM
Posts: 2,438
|
Re: Well, a first for me...
LOL, I have to say, that will be hard to top!
__________________
'52 F-1, EAB flathead |
Sponsored Links (Register now to hide all advertisements) |
|
09-30-2013, 11:39 PM | #3 |
Senior Member
Join Date: May 2010
Location: Above the gnat line in Georgia
Posts: 7,009
|
Re: Well, a first for me...
It gets worse as we go along.
__________________
Life is like a roll of toilet paper. The closer to the end, the faster it goes. It is better to be seen, than viewed. "We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm". |
09-30-2013, 11:48 PM | #4 |
Senior Member
Join Date: Jun 2012
Location: Gaylord, Michigan
Posts: 1,605
|
Re: Well, a first for me...
A lot worse when you turn 71 !
Just sayin'........! |
10-01-2013, 12:31 AM | #5 |
Senior Member
Join Date: May 2010
Location: Oakdale,Ca
Posts: 1,323
|
Re: Well, a first for me...
Dang...figured you'd all tell me I'd get smarter and make less mistakes!
Hanging head in sorrow...and running off to bed.... |
10-01-2013, 12:34 AM | #6 |
Senior Member
Join Date: Jul 2011
Location: SF Bay Area
Posts: 6,646
|
Re: Well, a first for me...
Sponsored Links (Register now to hide all advertisements)
__________________
Alan |
10-01-2013, 12:48 AM | #7 |
Senior Member
Join Date: Dec 2012
Location: Spokane Wa.
Posts: 271
|
Re: Well, a first for me...
I did it too, but I was only 60 then. Twelve years later I did it again!!
|
10-01-2013, 01:08 AM | #8 |
Senior Member
Join Date: May 2010
Location: Hansville, WA
Posts: 776
|
Re: Well, a first for me...
Hopefully whatever was on your mind was worth it..... :=)
|
10-01-2013, 01:45 AM | #9 |
Senior Member
Join Date: Aug 2012
Location: Perth, Western Australia
Posts: 2,687
|
Re: Well, a first for me...
DOh !!
__________________
"Came too close to dying to stop living now!" |
10-01-2013, 03:18 AM | #10 |
Senior Member
Join Date: May 2010
Location: Florence Ma.
Posts: 2,404
|
Re: Well, a first for me...
I would like to say you will never make a mistake like that again but then that would be my 1st lie of the day.
Now insult to injury your replacement line will never fit the way the 1st one did, LOL LOL Last edited by BILL WZOREK; 10-01-2013 at 03:19 AM. Reason: spelling |
10-01-2013, 05:37 AM | #11 |
Senior Member
Join Date: Aug 2010
Location: Oregon
Posts: 311
|
Re: Well, a first for me...
I've done most of what you've described, but not two ends w/out fittings! But now I probably couldn't even find my flaring tools!
|
10-01-2013, 01:00 PM | #12 |
Senior Member
Join Date: Jul 2011
Location: SF Bay Area
Posts: 6,646
|
Re: Well, a first for me...
Actually, the first flare wasn't a mistake. Common practice is to flare one end, drop on two fittings back to back, then flare the other end. Of course, this won't work if you bend the tube first.
__________________
Alan |
10-01-2013, 06:14 PM | #13 |
Senior Member
Join Date: May 2010
Location: Oakdale,Ca
Posts: 1,323
|
Re: Well, a first for me...
What I do is..when making up lines, is screw the "nut" into the W/C, then proceed to bend things to fit..making sure I can easily slide th etubing in and out...just to make sure I have the bend off the WC correct, so once flared and ready to screw in, I don't have to fight it... But...alas...with out the fitting on there.. Oh, and in response to the above...I did have to "stretch" the tubing a hair |
10-01-2013, 07:00 PM | #14 |
BANNED
Join Date: May 2010
Location: stratford,ct
Posts: 5,971
|
Re: Well, a first for me...
Its even worse at 74,LOL good one . ken ct.
|
10-01-2013, 07:45 PM | #15 |
Senior Member
Join Date: May 2010
Location: ManchVegas, New Hampshah
Posts: 1,589
|
Re: Well, a first for me...
Most definitely! "Now where did I put that tubing cutter I was just holding." You are experiencing just the beginning. Perfectly normal for an old codger. Welcome to the club.
__________________
You are never to old to enjoy your childhood. Forty1fordpickup on the HAMB. |
10-01-2013, 08:00 PM | #16 |
Senior Member
Join Date: May 2010
Location: Deer Lodge, MT
Posts: 658
|
Re: Well, a first for me...
Whew; you're not alone
Done that! Gets worse. Past 70. |
10-01-2013, 10:42 PM | #17 |
Senior Member
Join Date: Jul 2011
Location: SF Bay Area
Posts: 6,646
|
Re: Well, a first for me...
Done what? What gets worse? I'm alone here...
__________________
Alan |
10-02-2013, 05:02 AM | #18 |
Senior Member
Join Date: May 2010
Location: Chester Vt
Posts: 8,860
|
Re: Well, a first for me...
Yup!!
|
10-02-2013, 06:14 AM | #19 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,755
|
Re: Well, a first for me...
It's like the day when I made two new top shock brackets for my 33. Both left hand.
Mart. |
10-02-2013, 06:27 AM | #20 |
Senior Member
Join Date: May 2010
Posts: 218
|
Re: Well, a first for me...
My favorite saying is " there are only two types of people that don't make mistakes. Liars and people that don't do any thing ". That applies to younger people also.
|
10-02-2013, 07:18 AM | #21 |
Senior Member
Join Date: May 2010
Location: Illinois
Posts: 2,184
|
Re: Well, a first for me...
At 70 I notice that I sometime get the measure twice cut once rule backwards.
|
10-02-2013, 11:12 AM | #22 |
Senior Member
Join Date: Dec 2012
Location: Massillon, Ohio
Posts: 783
|
Re: Well, a first for me...
I went to the doctor a few months ago and was diagnosed with CRS Syndrome. (Can't Remember S**t) This may be what some of you guys have. I have noticed that CRS Syndrome,when working on cars sometimes results in LT Syndrome. (Lost Tool). This is not covered in Obamacare they tell me.
|
Sponsored Links (Register now to hide all advertisements) |
|
10-02-2013, 01:06 PM | #23 |
Senior Member
Join Date: May 2010
Location: Northern California,coast
Posts: 552
|
Re: Well, a first for me...
Try 81.... what was it now, oh yea, I lay out what I'am to do. then go back and look for the same parts twice, that I allready have out to do with, well enough, about me. thanks for asking ....OLD....BILL
|
10-02-2013, 01:22 PM | #24 |
Member
Join Date: May 2010
Location: Walterville, Or
Posts: 36
|
Re: Well, a first for me...
At 64 I thought the last 20 years were bad. Nice to know what I've got to look forward to.
|
10-02-2013, 07:54 PM | #25 |
Senior Member
Join Date: Jul 2013
Posts: 196
|
Re: Well, a first for me...
|
10-02-2013, 08:15 PM | #26 |
Senior Member
Join Date: May 2010
Location: Cottageville, WV
Posts: 1,535
|
Re: Well, a first for me...
Sponsored Links (Register now to hide all advertisements)
__________________
Son, you will never blow an engine up in high gear. |
10-02-2013, 10:31 PM | #27 |
Senior Member
Join Date: May 2010
Location: Oakdale,Ca
Posts: 1,323
|
Re: Well, a first for me...
Dang, can't insert BTO
Last edited by Mike B; 10-02-2013 at 10:32 PM. Reason: wrong |
10-03-2013, 05:18 PM | #28 |
Senior Member
Join Date: May 2010
Location: Corunna, Ontario, Canada
Posts: 309
|
Re: Well, a first for me...
Of all the things I've lost, I miss my mind the most! Byron.
__________________
IT'S NOT YOUR AGE, IT'S YOUR ATTITUDE ! |
10-03-2013, 06:13 PM | #29 |
Member
Join Date: Aug 2011
Location: MI
Posts: 55
|
Re: Well, a first for me...
Hang it on the wall in the garage as 1st place trophy, lol!! Thats what we do at the job when we "ALL GOOF" at some point or another. Over the years the trophies have become quite unique!!
__________________
Life is short, slow down and live it. http://www.flickr.com/photos/1942for...in/photostream |
10-03-2013, 06:54 PM | #30 |
Senior Member
Join Date: Feb 2011
Posts: 103
|
Re: Well, a first for me...
Just to make you all feel better.
You are all getting smarter because your forgetter is getting better |
10-20-2013, 10:27 AM | #31 |
Member
Join Date: Sep 2012
Location: Boulder, Colorado
Posts: 97
|
Re: Well, a first for me...
Uhhh, I just started my midlife crisis by entering my "Ford-ies"! I already have all these symptoms and just a couple of days to my 42'nd! You guys, please keep reporting these mistakes so I can try to avoid them! Thank you...
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|