|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
07-01-2010, 10:17 AM | #1 |
Senior Member
Join Date: May 2010
Location: Encino California, near Burbank
Posts: 935
|
Flywheel Identification
How do I determine if a flathead flywheel on the ground at a swapmeet is for an 8BA or earlier? Bought one drilled for ten inch plate and was concerned that I may have the wrong one. I had both the clutch and flywheel for less than five minutes and turned them over to Mario the clutch man at the same meet. What's the most obvious difference?
|
07-01-2010, 12:38 PM | #2 |
Senior Member
Join Date: May 2010
Location: Kaufman, TX
Posts: 822
|
Re: Flywheel Identification
Late model flywheel is steel, early model is cast iron and more subject to chatter if it gets a little oil on it. This is according to my friend who has been running flatheads since the 1950's.
|
Sponsored Links (Register now to hide all advertisements) |
|
07-01-2010, 01:16 PM | #3 |
Senior Member
Join Date: May 2010
Location: Encino California, near Burbank
Posts: 935
|
Re: Flywheel Identification?
I do recall that the flywheel that I bought was slightly dished out and dark on the engine side. Was in my posession so briefly that the concern about what I may have actually given to the clutch rebuilder motivates the question. I may have an 8BA flywheel to sell. Thanks: Fred A
|
07-01-2010, 02:35 PM | #4 |
Member
Join Date: May 2010
Posts: 82
|
Re: Flywheel Identification
There is a way to identify a 8BA flywheel from a 59a flywheel. The diference is in the ring gear. The 8ba ring gear is 5/8" wide and the 59a is 7/8" wide. This is the measurement from the I.D. where it's pressed on the flywheel out to the tip of the teeth.
This was lifted from XiX32 from the old Fordbarn. Try it and you will see it is so Bill |
07-01-2010, 03:43 PM | #5 |
Senior Member
Join Date: May 2010
Location: Minot, ND
Posts: 218
|
Re: Flywheel Identification
I've been told that the 8N/9N tractor ring gear is the same as the early ford V8 (3/4") Anyone know for sure?
|
07-01-2010, 04:23 PM | #6 |
Senior Member
Join Date: May 2010
Location: Cape Cod
Posts: 159
|
Re: Flywheel Identification
Sponsored Links (Register now to hide all advertisements)
http://flatheadv8.org/phpBB/viewtopi...flywheel#p1173 |
07-01-2010, 11:21 PM | #7 |
Senior Member
Join Date: May 2010
Location: Encino California, near Burbank
Posts: 935
|
Re: Flywheel Identification
That quarter inch difference in the starter ring is about distinctive enough. Won't soon be forgetting that one. There is still hope that what's in the shop is a 59A, which is what I need. Thanks: Fred A
|
07-02-2010, 09:28 AM | #8 |
Senior Member
Join Date: May 2010
Location: West Union, Ohio
Posts: 113
|
Re: Flywheel Identification
Note also that the crank recess is deeper on the early flywheel than on the 8BA. This places the ring gear closer to the front of the motor.
Jim
__________________
Visit my Blown '49 Merc website @ http://www.blown49.com |
07-02-2010, 05:56 PM | #9 |
Member
Join Date: May 2010
Location: South Australia
Posts: 50
|
Re: Flywheel Identification
|
07-02-2010, 08:13 PM | #10 |
Senior Member
Join Date: May 2010
Location: Encino California, near Burbank
Posts: 935
|
In and Out of Fashon Flatheads
In the fifties the engines of choice became the Olds/Cad and then as time went on, the Chevrolet V8 slowly was favored so that by '57 the flathead was considered to be boat anchors or worse. We had a new military surplus crate flathead (59L) under the bench that we tried to sell, then give away without much luck. My dad finally lied to a guy with an F100 panel, telling him that the engine would be a good spare for his machine. This was an era when a good part of the engines and speed stuff may have been scrapped. Luckily my family didn't ever sell the house and never really cleaned out the garage so many nice pieces of early V8 treasure survives. The flathead could go out of favor again yielding to V8s of the fifties and sixties or even inline engines that were never in favor during the era. Good luck: Fred A
|
07-03-2010, 08:52 AM | #11 |
Senior Member
Join Date: May 2010
Location: Cincinnati, OH
Posts: 1,361
|
Re: Flywheel Identification
Fred, I have one of the 59 type flywheels drilled for a 10" clutch. It has been surfaced and has a good ring gear on it. Let me know if you still need one. I also carry new ring gears if needed. The pics above are correct....the 8BA flywheel is basically flat on the back side where the 59 wheel is slightly dished.
__________________
VANPELT SALES LLC Cincinnati, Ohio Office: 513-724-9486 www.vanpeltsales.com www.classictransmission.com |
05-29-2015, 12:20 AM | #12 |
Senior Member
Join Date: May 2010
Location: Santa Fe Springs, California
Posts: 280
|
Re: Flywheel Identification
What is s good flywheel for my 59a?
__________________
I am a believer |
05-29-2015, 07:25 AM | #13 |
Senior Member
Join Date: Jul 2010
Posts: 2,593
|
Re: Flywheel Identification
A 59A flywheel.
Martin. |
05-29-2015, 08:44 AM | #14 |
Senior Member
Join Date: May 2010
Location: Canada Where it snows
Posts: 2,058
|
Re: Flywheel Identification
5 year old thread boy's
R |
05-29-2015, 04:45 PM | #15 |
Senior Member
Join Date: Jul 2010
Posts: 2,593
|
Re: Flywheel Identification
Thanks Ron, I missed that fact.
Still a much talked about thing though this flywheel compatibility, Or lack of. Still stands though, use the correct one. Martin. |
05-29-2015, 06:36 PM | #16 |
Senior Member
Join Date: May 2010
Location: Santa Fe Springs, California
Posts: 280
|
Re: Flywheel Identification
Original all ways is a good thing
__________________
I am a believer |
05-29-2015, 08:13 PM | #17 |
Senior Member
Join Date: May 2010
Location: Canada Where it snows
Posts: 2,058
|
Re: Flywheel Identification
A little more info to confirm with the resident guru's.
Don't 8ba's have the pressure plate bolt holes drilled all the way through and the 59a have blind pressure plate holes? Who knows this one. R |
05-30-2015, 08:38 AM | #18 |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,115
|
Re: Flywheel Identification
Very interesting observation, which I completely overlooked. DD
|
05-30-2015, 11:03 AM | #19 |
Senior Member
Join Date: May 2010
Location: Granger (Northern) Indiana
Posts: 1,520
|
Re: Flywheel Identification
|
05-30-2015, 12:40 PM | #20 |
Senior Member
Join Date: Jul 2010
Posts: 2,593
|
Re: Flywheel Identification
Went and checked my pile, it's a yep, 8BA drilled through, 59A and earlier blind holes.
Damn good observation Ronnie, Thanks, Martin. |
|
|
Sponsored Links (Register now to hide all advertisements) |
|