|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
11-15-2020, 12:04 AM | #1 |
Senior Member
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,375
|
Printable diagram for adjusting valve tappets
I've created a printable PDF with a diagram to assist with precise adjustment of valve clearances. This diagram is based on one created by FordBarn user Bob Johnson and shown in his video on valve adjusting.
As described on fordgarage.com, the tappet bolt spec is 24 threads per inch. This means that if you were to rotate the bolt 360° 24 times, it would change the clearance by 1". 24*360 = 8640° per 1-inch change. Therefore to change the clearance .001", or 1/1000 inches, you need to rotate the bolt 8640/1000 = 8.64°. The attached diagram shows lines marked on an arc in successive increments of 8.64°, each representing .001" difference in clearance from the next line. To adjust valve tappets using this diagram, you'll need to print it out and attach it to something rigid, like cardstock or cardboard. Cut a hole to center the diagram on the tappet. Measure your clearances as described on fordgarage.com above, and then, with the diagram in place, hold the tappet with one wrench while moving the adjusting wrench through the appropriate number of lines to get the clearance you want. See Bob's video for a demonstration. The PDF image is quite large in order to maximize the accuracy of the angles. You'll probably need to experiment with scaling it down to 80% or 60% to make it usable with your particular wrenches. |
11-15-2020, 12:34 AM | #2 |
Senior Member
Join Date: Jul 2016
Location: Orangeville Illinois
Posts: 462
|
Re: Printable diagram for adjusting valve tappets
This is very interesting, I have not seen this method before but will watch the video, print the image and a month or so down the road experiment. Thanks for sharing and taking the time to make the PDF.
|
Sponsored Links (Register now to hide all advertisements) |
|
11-15-2020, 12:35 AM | #3 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 5,979
|
Re: Printable diagram for adjusting valve tappets
Very interesting but I bet most would check with a feeler.
|
11-15-2020, 12:49 AM | #4 |
Senior Member
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,375
|
Re: Printable diagram for adjusting valve tappets
|
11-15-2020, 03:24 AM | #5 |
Senior Member
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,511
|
Re: Printable diagram for adjusting valve tappets
I do similar. If one turn is 1/24th of an inch (0.042"), then one face on the hexagonal adjuster is 1/6th of that (0.007"). It doesn't take long to learn how much to move the spanner to get 1 or 2 thou movement. I always check with feelers after every adjustment.
(If the motor is out of the car, it doesn't take long but with it in the car, it is a bear with a RHD car.)
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood. |
11-15-2020, 01:58 PM | #6 |
BANNED
Join Date: Dec 2019
Posts: 1,196
|
Re: Printable diagram for adjusting valve tappets
Sponsored Links (Register now to hide all advertisements)
|
11-16-2020, 12:10 PM | #7 | |
Senior Member
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,056
|
Re: Printable diagram for adjusting valve tappets
Quote:
__________________
If you don't hear a rumor by 10 AM, start one!. Got my education out behind the barn! |
|
11-16-2020, 12:35 PM | #8 |
Senior Member
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,375
|
Re: Printable diagram for adjusting valve tappets
Don't worry, if you decide you don't need to use this diagram, I will not be offended.
|
11-16-2020, 02:34 PM | #9 |
Senior Member
Join Date: Aug 2016
Location: West Virginia
Posts: 430
|
Re: Printable diagram for adjusting valve tappets
I always just did it with two fielders gauges. One too big and one too small and adjust to go and not go. This one makes my head hurt.
|
11-16-2020, 03:46 PM | #10 |
Senior Member
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,511
|
Re: Printable diagram for adjusting valve tappets
The two methods are very similar. They both use the pitch of the thread to work out how far to turn the adjustment. IMO, you have just taken it one step further with your diagram while I rely more on "feel".
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood. |
11-16-2020, 04:04 PM | #11 | |
Senior Member
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,375
|
Re: Printable diagram for adjusting valve tappets
Quote:
|
|
11-16-2020, 04:29 PM | #12 | |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 5,979
|
Re: Printable diagram for adjusting valve tappets
Quote:
|
|
11-16-2020, 04:38 PM | #13 | |
Senior Member
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,375
|
Re: Printable diagram for adjusting valve tappets
Quote:
|
|
11-19-2020, 02:26 AM | #14 |
Senior Member
Join Date: May 2010
Location: ACT Australia
Posts: 507
|
Re: Printable diagram for adjusting valve tappets
Hi alexiskai, would love to watch the video, but it appears the link may be broken?
|
11-19-2020, 10:07 AM | #15 |
Senior Member
Join Date: Apr 2013
Location: Fairport, NY
Posts: 133
|
Re: Printable diagram for adjusting valve tappets
I just noticed that the video link was non-responsive. Can we have another link -or- connection? Thank You!!
|
11-19-2020, 01:13 PM | #16 | ||
Senior Member
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,375
|
Re: Printable diagram for adjusting valve tappets
Quote:
Quote:
http://www.modelahouse.com/movies/valves.wmv You can also go to the root page and click on "Valve adjusting": http://www.modelahouse.com/movies/index.html Once the file downloads, most folks should have a media player on their Mac/PC that'll run it. Last edited by alexiskai; 11-19-2020 at 02:12 PM. |
||
12-25-2020, 08:35 PM | #17 |
Senior Member
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,375
|
Re: Printable diagram for adjusting valve tappets
Following up, this is the setup that worked for me when adjusting my valve lash. I had to cut down the diagram a bit because of the size I printed it at; otherwise you can't get at the #1 and #8 valves. I spray-glued it to cardboard and then taped a thin wrench to the back. That wrench holds the tappet while the 1/2" wrench does the adjusting.
|
12-25-2020, 10:48 PM | #18 |
Senior Member
Join Date: Jun 2014
Location: Land of Lincoln
Posts: 3,136
|
Re: Printable diagram for adjusting valve tappets
Thank you and Bob Johnson for sharing ! Soooo how did she run after adjusting the lash?
__________________
Don't force it with a little hammer tap, tap, tap get a bigger hammer tap done |
12-25-2020, 10:57 PM | #19 |
Senior Member
Join Date: Feb 2011
Posts: 2,115
|
Re: Printable diagram for adjusting valve tappets
Doing valves this weekend, thanks for sharing!
__________________
Tim Downtown, Ca |
12-25-2020, 11:22 PM | #20 |
Senior Member
Join Date: May 2010
Location: Portland OR
Posts: 6,346
|
Re: Printable diagram for adjusting valve tappets
I learned this way of doing it from a post on the Model T Ford Club of America years ago, doing by thread count and degrees. Works very well. I also check with the feeler gauge to make sure it is good. Thanks for posting this. Great idea on the degrees gauge.
__________________
I know the voices aren't real but damn they have some good ideas! |
|
|
Sponsored Links (Register now to hide all advertisements) |
|