|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
08-31-2018, 07:27 AM | #1 |
Senior Member
Join Date: Aug 2018
Posts: 2,332
|
Nu-rex Timing wrench
Anybody have experience using this? Are they OK/worthwhile, or just good enough as a quick ballpark tool to get you up and running? http://www.nurex.com/timing
|
08-31-2018, 08:15 AM | #2 |
Senior Member
Join Date: Nov 2011
Location: San Diego, CA
Posts: 442
|
Re: Nu-rex Timing wrench
Two thoughts:
- You're going to need a wrench to hold the cam anyways, so why not get one that'll pull double-duty? - It does a pretty good job at setting timing; and with the manual spark advance on our cars, how exacting does timing have to be at idle anyways? As soon as you put the car into gear, you'll be changing the timing a whole lot more than any possible small error that this wrench might have. |
Sponsored Links (Register now to hide all advertisements) |
|
08-31-2018, 09:00 AM | #3 | |
Senior Member
Join Date: Apr 2011
Location: Endeavor, WI
Posts: 119
|
Re: Nu-rex Timing wrench
Quote:
That has to be the most brilliant thing I've ever seen said on this forum.
__________________
"I have not yet begun to defile myself." -Doc Holliday '31 Tudor, '69 F100, '66 Mustang, '11 Ford Flex |
|
08-31-2018, 09:06 AM | #4 |
Senior Member
Join Date: May 2010
Location: Young Harris, GA
Posts: 1,821
|
Re: Nu-rex Timing wrench
It does a pretty good job, especially when you find yourself at the side of the road in need of checking or setting the timing on your car (or another car touring with you). But it's certainly not the only way to set the timing, and many experienced Model A guys pooh-pooh it as not necessary.
The design and the instructions they give you on how to use it help you get the slack out of the distributor drive shaft and drive gear mechanism as you set the timing. Not doing this is the most common reason people get their initial timing wrong, so it prevents the most common error made. It's also a good choice for guys that are not comfortable with electrical stuff, like test lights and ohmmeters. There is really nothing to do except set the engine on TDC with the timing pin and then check/set the timing with the wrench. Almost foolproof. Almost. If you want to see how good of a job it does, use the tool per the instructions, then check the results with a test light or meter, per normal shop timing procedure. I found it to set the timing just a few degrees after TDC, which is good enough for me. Fast and easy. YMMV.
__________________
Jim Cannon Former MAFCA Technical Director "Have a Model A day!" |
08-31-2018, 09:13 AM | #5 | |
Senior Member
Join Date: Aug 2018
Posts: 2,332
|
Re: Nu-rex Timing wrench
Quote:
I agree, I was also thinking around those lines too, but wanted a second opinion. With slop in the distributor, gears, advance linkage, fit of the distributor plastic body, etc. Did not think timing had to be a huge concerns if proper within a degree or 2 or 3. If out of adjust a small amount, the advance lever takes care of it. Will get one and try it, cheap, and always like buying new toys. Thanks. |
|
08-31-2018, 10:46 AM | #6 |
Senior Member
Join Date: Jun 2015
Posts: 1,414
|
Re: Nu-rex Timing wrench
Sponsored Links (Register now to hide all advertisements)
|
08-31-2018, 11:05 AM | #7 | |
Senior Member
Join Date: Aug 2018
Posts: 2,332
|
Re: Nu-rex Timing wrench
Quote:
Thanks for the info. Already ordered it, only a few bucks. Currently use meter with a buzzer across the points. Buzzes, stops buzzing when point open. Prefer this so I do not have to constantly check a bulb. Do the buzzer 1st, then check the adjust with the wrench. Figure if the Nu wrench is off, modify it's handle material - remove material or add(jb weld it) a washer at the check spot on handle at the check point. |
|
08-31-2018, 12:29 PM | #8 |
Senior Member
Join Date: Apr 2015
Location: Saint Cloud Mn
Posts: 745
|
Re: Nu-rex Timing wrench
About as accurate as you can get without a timing light. Close enough for a model A. Once running splitting hairs at idle retard is a moot point anyway. The wrench works just fine and is a lot easier.
|
08-31-2018, 01:06 PM | #9 |
Senior Member
Join Date: Jun 2013
Location: Western Springs, IL
Posts: 324
|
Re: Nu-rex Timing wrench
I too concur that it is a good tool to use to set everything as correct as necessary for a model A. As others have stated, once started, you will be changing the spark so it is a moot point as to perhaps 2-3 degrees off from the absolute recommendations for the set point. I have used one for several years now on my car and others and when checked afterwards was quite accurate.
|
08-31-2018, 01:12 PM | #10 |
Senior Member
Join Date: Aug 2018
Posts: 2,332
|
Re: Nu-rex Timing wrench
Thanks to all who responded. According to y'all, like a great alternate way of timing.
|
08-31-2018, 01:13 PM | #11 |
Senior Member
Join Date: May 2010
Location: Between Seattle & Tacoma
Posts: 2,354
|
Re: Nu-rex Timing wrench
I don’t understand why the timing must be set so much. Everyone says I checked the timing———— blah blah blah. Once it’s set, it’s set. How can it change. Yes, I know the points as they change, affect timing, but once you reset the points, it’s back to where you set it originally. Slop doesn’t matter because the engine turning removes it.
|
08-31-2018, 01:52 PM | #12 |
Senior Member
Join Date: Nov 2010
Location: Anchorage, Alaska
Posts: 9,115
|
Re: Nu-rex Timing wrench
Voice of experience here:
On a tour a couple years ago, one of our members had a failure with his dizzy. Not sure what the problem was, but he wound up just replacing the dizzy with a spare he had along. Then spent the next 30-45 minutes trying to time it correctly. Finally, I asked if anyone had one of the Nu-Rex tools. One magically appeared from the depths of stuff the several guys standing around had. Using the Nu-Rex tool, I was able to time his dizzy and get everyone back on the road in 5 minutes. I now carry one in my tool bag all the time.
__________________
Alaskan A's Antique Auto Mushers of Alaska Model A Ford Club of America Model A Restorers Club Antique Automobile Club of America Mullins Owner's Club |
08-31-2018, 02:16 PM | #13 | |
Senior Member
Join Date: Dec 2014
Location: Germantown,TN
Posts: 516
|
Re: Nu-rex Timing wrench
Quote:
|
|
08-31-2018, 05:18 PM | #14 |
Senior Member
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,496
|
Re: Nu-rex Timing wrench
I've been posting that for years and only got flack for it!! I still maintain some of us show our OCD when it comes to setting the timing.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood. |
08-31-2018, 08:39 PM | #15 | |
Senior Member
Join Date: May 2010
Location: wheeling west virginia
Posts: 231
|
Re: Nu-rex Timing wrench
Quote:
|
|
08-31-2018, 09:32 PM | #16 | |
Senior Member
Join Date: May 2010
Location: Central, IL
Posts: 3,968
|
Re: Nu-rex Timing wrench
Quote:
A dime is about .050", penny .060", nickel .075". A plastic gift card is .030" so roughly spark plug gap. Pretty much just need Ford tool kit, roll of electrical tape, pocket knife, and about 3 feet of steel wire and a bunch of Mac Guyver knowledge to utilize what you have on you.
__________________
1929 Model AA - Need long splash aprons! |
|
09-01-2018, 01:45 PM | #17 |
Senior Member
Join Date: Nov 2010
Location: Anchorage, Alaska
Posts: 9,115
|
Re: Nu-rex Timing wrench
Back in "the day" when paper matchbooks were plentiful, they were about .015" thick, just right for most points.
__________________
Alaskan A's Antique Auto Mushers of Alaska Model A Ford Club of America Model A Restorers Club Antique Automobile Club of America Mullins Owner's Club |
09-01-2018, 02:05 PM | #18 | |
Senior Member
Join Date: Aug 2018
Posts: 2,332
|
Re: Nu-rex Timing wrench
Quote:
Just looked up this tool on Snyder's and looked at the instructions. Without having the tool, could not make sense of the instructions. I got the impression it allows you to gap the points without need to rotate the motor to find the high spot on the cam? Yes? No? If yes that would be handy on the road with a hot engine, hot day, or on a rainy day. |
|
09-01-2018, 02:10 PM | #19 |
Senior Member
Join Date: Aug 2018
Posts: 2,332
|
Re: Nu-rex Timing wrench
|
09-01-2018, 05:33 PM | #20 |
Senior Member
Join Date: May 2010
Location: wheeling west virginia
Posts: 231
|
Re: Nu-rex Timing wrench
30 closed cab pickup..post no. 39...the answer is YES..Thats the point i was trying to make..really simple..you don't have to find the high on the cam. If you ever find you have to adjust the points on the open road, this really makes it nice.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|