|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
05-13-2010, 07:21 AM | #1 |
Senior Member
Join Date: May 2010
Location: ASTON, PA.
Posts: 725
|
1929 fordor leatherback
Hello all,
I am working on a friends 29 leather back, older restoration he wants all the doors alligned. the doors are to close to the door jams at the hinges and sagging at the door handles. any help would be helpful. Mike |
05-13-2010, 07:33 AM | #2 |
BANNED
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
|
Re: 1929 fordor leatherback
|
Sponsored Links (Register now to hide all advertisements) |
|
05-13-2010, 07:45 AM | #3 |
Senior Member
Join Date: May 2010
Location: Shrewsbury,Pa
Posts: 513
|
Re: 1929 fordor leatherback
I am in the middle of a total resoration of a 29 Leatherback. Its first time restored. All the wood is rotten where any fitting, bolt, screw, or nail was used. In the areas that were not bad the wood was dried out and brittle and would not hold screws well.I'm replacing all of it. If your frame is sagged and it probably is and the wood is bad at the joints I don't see how any door adjustment can last long term. If it is an older restoration was the wood replaced at that time. There are different opinions on what constitutes a restoration. Overspraying the exterior, installing new interior and a majored engine is not restored to me it's extensive maintanence.
|
05-13-2010, 09:52 AM | #4 |
Senior Member
Join Date: May 2010
Location: ASTON, PA.
Posts: 725
|
Re: 1929 fordor leatherback
Thanks Mitch, and Bill
I will try some shims but I think Bill is right. Do it right cry once do it wrong cry alot mike |
05-14-2010, 04:10 PM | #5 |
Senior Member
Join Date: May 2010
Location: Naperville, IL
Posts: 1,387
|
Re: 1929 fordor leatherback
I purchased a roll of 1/16" thick fabric reinforced rubber which is quite similar to what was original to my Fordor. Made shims using multi layers of the material to allign the doors. The effort was time consuming. I did not like the material available from the suppliers since it was too soft and compressed too much.
|
05-14-2010, 05:16 PM | #6 |
Senior Member
Join Date: May 2010
Location: Richlands, VA
Posts: 533
|
Re: 1929 fordor leatherback
Sponsored Links (Register now to hide all advertisements)
Yes, it was costly, but is worth it in the long run. I must say that it is extremely difficult to find a wood craftman. They are far and few between. And unless you have wonderful woodworking skills, I would not attempt it. |
05-14-2010, 07:02 PM | #7 |
Senior Member
Join Date: May 2010
Location: Western PA
Posts: 118
|
Re: 1929 fordor leatherback
When I restored my 29 Leatherback (60B), I found all the body wood was rotten or dried out and in some cases sawdust, which made all body parts sag.
I decided to use Red Oak and obtained enough to do everything for less than $300. It took me 5 months to rebuild the entire wooden structure. Many of the pieces were nothing but sawdust. It took every bit of my skill to reproduce them. Here is the end result. |
05-14-2010, 07:54 PM | #8 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: 1929 fordor leatherback
A friend has the original right and left sill pieces from his 1930 Murray Town Sedan. I don't know how anyone could reproduce them without having these in person to copy from. It's a lot of work for sure! But, when done the Fordors make the best Model A's there are for comfort, and good looks.
|
05-14-2010, 08:09 PM | #9 |
Senior Member
Join Date: May 2010
Location: Toronto, Ontario, Canada
Posts: 1,289
|
Re: 1929 fordor leatherback
Make mine a slant window Tom, but please do the wood first!
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|