12-18-2021, 04:34 PM | #1 |
Senior Member
Join Date: May 2010
Location: Moncks Corner, SC
Posts: 439
|
Fenton Headers
Fenton headers on a 1940 24 stud. One bolt will not thread. I give up. Not my car but doing an engine change for an elderly friend. I spent way too much time trying to get one bolt to thread. The design looks like the designer was on crack. POS Fenton headers they are...
|
12-18-2021, 04:49 PM | #2 |
Senior Member
Join Date: Jul 2011
Location: SF Bay Area
Posts: 6,646
|
Re: Fenton Headers
Front bolts are 7/16-16, all the rest are 3/8-16. Welcome to Ford Flatheads.
__________________
Alan |
Sponsored Links (Register now to hide all advertisements) |
|
12-18-2021, 04:53 PM | #3 | |
Senior Member
Join Date: May 2010
Location: Charlotte NC KiWi-L100 available here
Posts: 2,963
|
Re: Fenton Headers
Quote:
|
|
12-18-2021, 05:30 PM | #4 |
Senior Member
Join Date: Dec 2010
Location: East Coast in CT
Posts: 1,529
|
Re: Fenton Headers
This fellow may have a set of off shore knocks off. The instructions should read due to accumulated tolerances some adjustment is required.
__________________
I use the F word a lot no not that word these words Flathead , Focus and Finish. "Life Member of the Bonneville 200 MPH Club using a Ford Flathead block" Owner , Builder, Driver of the First Ford Flathead bodied roadster to run 200 MPH Record July 13, 2018 LTA timing association 200.921 in one and a half miles burning gasoline. First ever gas burning Ford flathead powered roadster to run 200 MPH at Bonneville Salt Flats setting the record August 7th 2021 at 205.744 MPH |
12-18-2021, 05:50 PM | #5 |
Senior Member
Join Date: Feb 2011
Posts: 794
|
Re: Fenton Headers
|
12-18-2021, 06:00 PM | #6 |
Senior Member
Join Date: May 2010
Posts: 4,484
|
Re: Fenton Headers
Sponsored Links (Register now to hide all advertisements)
|
12-18-2021, 06:21 PM | #7 |
Senior Member
Join Date: Jul 2011
Location: SF Bay Area
Posts: 6,646
|
Re: Fenton Headers
You are correct. My bad.
__________________
Alan |
12-18-2021, 06:29 PM | #8 |
Senior Member
Join Date: May 2010
Posts: 2,488
|
Re: Fenton Headers
Ran into the same problem with engine holding [mount] exhaust plate-Some adjustment of holes required Newc
|
12-18-2021, 10:35 PM | #9 |
Senior Member
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,577
|
Re: Fenton Headers
I have a set, bought from a swap meet, but new-ish looking, I assume speedway Chinese mfr, and they fit just fine. Got a rat tail file?
|
12-19-2021, 12:48 AM | #10 | |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,114
|
Re: Fenton Headers
Quote:
Just be sure it's a USA-made rat-tail file! Otherwise, make'm funny holes! DD . |
|
12-19-2021, 02:09 AM | #11 |
Senior Member
Join Date: Jul 2011
Location: SF Bay Area
Posts: 6,646
|
Re: Fenton Headers
I’m in before the hammer!
__________________
Alan |
|
|
Sponsored Links (Register now to hide all advertisements) |
|