|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
09-24-2016, 03:29 PM | #1 |
Junior Member
Join Date: Sep 2016
Location: S W MO.
Posts: 6
|
brake&clutch cross shaft 32 ford
what is the dimension from tip of frame to the cross shaft ?????
|
09-24-2016, 03:31 PM | #2 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: brake&clutch cross shaft 32 ford
Do you have the frame diagram? Would that be of any help? That would give you the mounting surface maybe.
And welcome to the Barn!!! |
Sponsored Links (Register now to hide all advertisements) |
|
09-24-2016, 03:43 PM | #3 |
Senior Member
Join Date: May 2010
Location: Southern California
Posts: 7,033
|
Re: brake&clutch cross shaft 32 ford
I am not sure I understand the question? The cross shaft is a bracket that bolts to the K member. What tip of the frame are you talking about. What are you trying to do? Here is a diagram for the frame in case you don't already have it: http://wescottsauto.com/WebCatalog/T...iagram1932.pdf
And, welcome to the Barn. Charlie Stephens |
09-24-2016, 03:49 PM | #4 |
Junior Member
Join Date: Sep 2016
Location: S W MO.
Posts: 6
|
Re: brake&clutch cross shaft 32 ford
i have all the frame charts had them all enlarged and laminated they are pretty
helpful but they lack some important figures thank for the reply |
09-24-2016, 03:53 PM | #5 |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,114
|
Re: brake&clutch cross shaft 32 ford
Great, BUT.......like Charlie asked you above, which "tip" of the frame are you talking about? DD
|
09-24-2016, 03:56 PM | #6 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: brake&clutch cross shaft 32 ford
Sponsored Links (Register now to hide all advertisements)
Now that I think about it this is a rather interesting guessing game! |
09-24-2016, 03:58 PM | #7 |
Junior Member
Join Date: Sep 2016
Location: S W MO.
Posts: 6
|
Re: brake&clutch cross shaft 32 ford
i would like to have the mesurement from the tip of the frame to the center line of the
peddle shaft |
09-24-2016, 04:00 PM | #8 |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,114
|
Re: brake&clutch cross shaft 32 ford
the front tip, the rear tip, the side tip, the bottom tip.........what friggen' tip? Dd
|
09-24-2016, 04:01 PM | #9 |
Junior Member
Join Date: Sep 2016
Location: S W MO.
Posts: 6
|
Re: brake&clutch cross shaft 32 ford
tip of front frame horn it is a new chassis
|
09-24-2016, 04:02 PM | #10 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: brake&clutch cross shaft 32 ford
Ok, now that we have which tip, what part of the tip, top, bottom, center ... Problem is it's a curved surface and not parallel to much of anything. Going to be hard to get a very precise measurement AND I would doubt that a repo frame would match up very well with an original anyway. It may be a little difficult to end up with what you need. Is there a reason you need the tip of the frame? Another landmark might work better.
If this is going to be a none flathead installation there might be better resources for what you are looking for. The pedal assembly bolts to the K-member, the diagram posted above provides the dimensions to the K-member. So all that is left (assuming you don't have an original set of pedals) is the distance from the front face of the K-member to the centerline of the pedal assembly, correct? Last edited by JSeery; 09-24-2016 at 04:50 PM. |
|
|
Sponsored Links (Register now to hide all advertisements) |
|