|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
05-18-2024, 03:32 PM | #1 |
Junior Member
Join Date: May 2024
Location: Albany,NY
Posts: 17
|
UPDATE***39 Ford deluxe can't remove cam
Heads off, intake off, all valves are pinned up with wedges, all the lifters are pinned up as well, CAM will not come out, it's hitting some stop somewhere.....anyone know blocking it?
Do I rotate cam or crank and continue to pull on camshaft? They are "separated' because I have missing teeth on the camshaft, engine still in car, trying to repair while in car. Any help appreciated. Tom Last edited by Turbofan; 05-19-2024 at 11:20 AM. |
05-18-2024, 03:45 PM | #2 |
Senior Member
Join Date: May 2010
Posts: 1,779
|
Re: 39 Ford deluxe can't remove cam
make sure fuel pump push rod is out
|
Sponsored Links (Register now to hide all advertisements) |
|
05-18-2024, 04:10 PM | #3 |
Senior Member
Join Date: May 2010
Location: Powell, TN
Posts: 2,519
|
Re: 39 Ford deluxe can't remove cam
see which lifter does not move when you pull the cam fwd.
|
05-18-2024, 05:25 PM | #4 |
Junior Member
Join Date: May 2024
Location: Albany,NY
Posts: 17
|
Re: 39 Ford deluxe can't remove cam
Everything is pinned up. Are you saying it's still getting caught on one of the lifters?
|
05-18-2024, 05:29 PM | #5 |
Senior Member
Join Date: Apr 2019
Location: Kansas
Posts: 1,014
|
Re: 39 Ford deluxe can't remove cam
This? And if one lifter isn't quite high enough the cam will catch it.
__________________
"It don't take but country smarts to solve the problem" (Smokey Yunick) '41 Merc Town Sedan / 260" 8CM engine '66 Fairlane four door / "warmed up" 302 |
05-19-2024, 05:16 AM | #6 |
Junior Member
Join Date: May 2024
Location: Albany,NY
Posts: 17
|
Re: 39 Ford deluxe can't remove cam
Sponsored Links (Register now to hide all advertisements)
I still can't get my cam out, it's going up against a hard stop somewhere.....all the valves and lifters are pinned up. Thx |
05-19-2024, 06:03 AM | #7 |
Senior Member
Join Date: May 2010
Posts: 2,180
|
Re: 39 Ford deluxe can't remove cam
Probably just a lobe getting hung up on a bearing hole as you're trying to slide it out.
|
05-19-2024, 06:29 AM | #8 |
Senior Member
Join Date: May 2010
Location: NJ
Posts: 6,276
|
Re: 39 Ford deluxe can't remove cam
Can you rotate it or will it not spin either?
|
05-19-2024, 06:45 AM | #9 |
Senior Member
Join Date: May 2010
Posts: 4,804
|
Re: 39 Ford deluxe can't remove cam
The pressed on gear does not have a retainer to remove. Suggest drill small holes on the gear where it attaches to the cam to release the broken cam gear.
|
05-19-2024, 07:48 AM | #10 |
Member
Join Date: Feb 2015
Posts: 44
|
Re: 39 Ford deluxe can't remove cam
I’m reading that you have all the parts you mentioned lifted out of the way, Richard Crow asked if you had the fuel pump push rod pulled back, you didn’t list that, you didn’t respond to Mr. Crow. Could that push rod be the issue?
|
05-19-2024, 08:25 AM | #11 |
Senior Member
Join Date: Dec 2014
Location: Columbus, IN
Posts: 1,413
|
Re: 39 Ford deluxe can't remove cam
I had the same issue on my 1937 21 stud engine. The difference was that the engine was out of the car, all the lifters were out of the engine and the fuel pump pushrod. The cam would move 1/4”-1/2” and then felt like it was hitting something. I then removed the rear idler gear cover, behind the flywheel, but that didn’t help. I then used some gentle taps on the rear end of the camshaft and was able to remove the cam. My thought was there were some deposits on the cam journals that prevented its removal. I wish you luck with your project.
Last edited by Zeke3; 05-19-2024 at 08:26 AM. Reason: Clarification |
05-19-2024, 11:55 AM | #12 |
Junior Member
Join Date: May 2024
Location: Albany,NY
Posts: 17
|
Re: UPDATE***39 Ford deluxe can't remove cam
Cam finally came out, pulled, hammered, pulled hammered.
Does anyone have a camshaft for sale with a metal gear? Last edited by Turbofan; 05-19-2024 at 12:04 PM. |
05-19-2024, 01:27 PM | #13 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 11,050
|
Re: UPDATE***39 Ford deluxe can't remove cam
If your engine uses cam bearings be sure and check their condition after all that pulling and hammering.
|
05-19-2024, 05:40 PM | #14 |
Senior Member
Join Date: Jan 2011
Location: Central Ohio
Posts: 5,257
|
Re: UPDATE***39 Ford deluxe can't remove cam
Just assume you'll need new cam bearings . . . they are not expensive.
|
05-19-2024, 07:24 PM | #15 | |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,135
|
Re: UPDATE***39 Ford deluxe can't remove cam
Quote:
Just make sure they're NOT the 0.011" oversize (IF I remember correctly) that folks occasionally run into, possibly used at factory to correct blocks with that deficiency, thus rejection of block, otherwise. Coop . |
|
05-20-2024, 04:51 AM | #16 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,800
|
Re: UPDATE***39 Ford deluxe can't remove cam
You can also have undersize bearings. I have a cam that is 10 thou under.
|
05-20-2024, 05:13 AM | #17 |
Junior Member
Join Date: May 2024
Location: Albany,NY
Posts: 17
|
Re: UPDATE***39 Ford deluxe can't remove cam
I'm not replacing the cam bearings if this even has cam bearings, the journals and lobes on mine are clean with no pitting. I would reuse this cam if not for the press on gear type.
Can anyone recommend a new Cam and gear including parts numbers? What lift and duration am I looking for ideally? I generally stay stock unless there's a cam that will provide some improvements that I can just drop in. |
05-20-2024, 07:21 AM | #18 |
Senior Member
Join Date: May 2010
Location: upstate SC
Posts: 2,986
|
Re: UPDATE***39 Ford deluxe can't remove cam
press on one of the metal gears-yes you can get them early ford v8 in sc has them
|
05-20-2024, 07:24 AM | #19 |
Senior Member
Join Date: Jan 2011
Location: Central Ohio
Posts: 5,257
|
Re: UPDATE***39 Ford deluxe can't remove cam
The cam you have is all nice and cozy with the lifters you have - if it is in good shape, put a new gear on it and put er' back in!
|
05-21-2024, 05:02 AM | #20 |
Junior Member
Join Date: May 2024
Location: Albany,NY
Posts: 17
|
Re: UPDATE***39 Ford deluxe can't remove cam
New fiber gear??? I can't find a press on metal gear!
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|