What did you do today that was flathead V8 related?

[petehoovie]

Originally Posted by Ziggster

Been messing with the copper coolant pipes for my rear mounted rad on my speedster project for the last month and a half. Trying to make a mount/support using the fuel pump/breather tube for the copper pipes coming off of the heads.

[ndnchf]

I went to the Charlotte Auto Fair last week. I came home with a pile of generator cores for rebuilding. So I've been going through and sorting them out.

[petehoovie]

Originally Posted by ndnchf

I went to the Charlotte Auto Fair last week. I came home with a pile of generator cores for rebuilding. So I've been going through and sorting them out.

[BoxCar Tom]

In response to a Want Ad I spent at least 2 hours last night taking pictures of two disassembled 32 column "drops", then move the pictures to my computer to reorient them, then move the pictures to an email, then write an email with an accurate description of each drop. Well what else am I doing from 11 PM to 1 AM?

[petehoovie]

Originally Posted by BoxCar Tom

In response to a Want Ad I spent at least 2 hours last night taking pictures of two disassembled 32 column "drops", then move the pictures to my computer to reorient them, then move the pictures to an email, then write an email with an accurate description of each drop. Well what else am I doing from 11 PM to 1 AM?

[TonyM]

Sponsored Links (Register now to hide all advertisements)

I wrote a check.

[TomT/Williamsburg]

I drove mine all over town today!

[RalphM]

Got the interior out and most of the floor cleaned up on the 47 Coupe. Just going to wire brush it, replace body seam caulking, and POR it.
Replacing body mounts at the same time.

[petehoovie]

Originally Posted by RalphM

Got the interior out and most of the floor cleaned up on the 47 Coupe. Just going to wire brush it, replace body seam caulking, and POR it.
Replacing body mounts at the same time.

[tubman]

Logged into "The Ford Barn" about 6 times!

[deuce_roadster]

Only worked on Brand X today but like tubman, logged on here.

[BoxCar Tom]

Only 6 Times?

[Scott52]

Moved car back to my garage from storage. My wife will make the seat covers and the engine is getting ready to go back in.

[Scott52]

Oh and I had to move the Dodge Power Wagon (230 Flathead) out of the garage to make room.

[Newc]

Drove 60 miles to looook at a Free pile of mechanical parts, then drove home. Just not worth messing with 5 pallets of mechanicals. Even a Y block 292" Trk 4 speed too. Newc

[petehoovie]

Originally Posted by Scott52

Moved car back to my garage from storage. My wife will make the seat covers and the engine is getting ready to go back in.

[1934]

I got the '34 out of the barn yesterday after it's winter rest. It didn't want to wake up at first and was a bit cranky, LOL. A bit of gas down the carb and she perked right up! There was still a bit of residual salt on our roads here so I didn't go for a drive. I changed the oil and it rained quite a bit last night so maybe I'll put a few miles on it today.
Doug.

[ndnchf]

I was working on a local club member's generator. It had a threaded on, fan mount pulley. These are often tight and a bear to remove. Being a fan mount pulley, I was able to unscrew it using an old fan as a wrench with the armature in a padded vise and a little heat.

[farmertom]

well,i drive my,'37 daily at least for 30 mins to hour or so. couple days ago got her up on all fours and performed all maint. oil change,lubed zerks,springs,checked trans.,diff,oiled gen.and,distributer. also new coil and condenserTom.

[petehoovie]

Originally Posted by ndnchf

I was working on a local club member's generator. It had a threaded on, fan mount pulley. These are often tight and a bear to remove. Being a fan mount pulley, I was able to unscrew it using an old fan as a wrench with the armature in a padded vise and a little heat.