|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
05-29-2019, 05:37 PM | #1 |
Senior Member
Join Date: Feb 2011
Posts: 253
|
Holley 94 vacuum line fitting
Guys,
Is there such thing as an oversize brass fitting for the vacuum line connection on a Holley 94 carb as used on 48 and up truck motors and 49 up car motors? This is the port for the hard line going to the advance can on the distributor. My port looks fine, threads look good, but none of my three good hard lines with associated brass fittings thread up. Its like the port and threads in the carb are one size bigger than normal. This is on a spare carb I just had rebuilt. Ofcccourse I only noticed when I went to install the carb... Thanks in advance. |
05-29-2019, 06:40 PM | #2 |
Senior Member
Join Date: Nov 2010
Location: NM
Posts: 2,438
|
Re: Holley 94 vacuum line fitting
Are you sure you have the correct fitting on the line? New ones can be had from NAPA, although not usually stocked.
__________________
'52 F-1, EAB flathead |
Sponsored Links (Register now to hide all advertisements) |
|
05-29-2019, 08:55 PM | #3 |
Senior Member
Join Date: Feb 2011
Posts: 253
|
Re: Holley 94 vacuum line fitting
Right fittings, too big hole...
|
05-30-2019, 01:33 AM | #4 |
Senior Member
Join Date: May 2010
Location: MN
Posts: 7,053
|
Re: Holley 94 vacuum line fitting
It's fair to say it's been opened up.
|
05-30-2019, 09:13 AM | #5 |
Senior Member
Join Date: Dec 2011
Location: Oakville Ontario
Posts: 586
|
Re: Holley 94 vacuum line fitting
if it is not the one ross showed then as tinker said somebody has monkeyed with it.good luck as you know that has to seal tight.
|
05-30-2019, 09:39 AM | #6 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,950
|
Re: Holley 94 vacuum line fitting
Sponsored Links (Register now to hide all advertisements)
Sounds crazy but could you use Teflon tape or RTV sealer on the fitting? Could you first insert a very thin piece of thin walled plastic tubing with some Permatex sealer in the hole and then screw in the OEM fitting a little at a time making the threads as it goes in ? |
05-30-2019, 09:58 AM | #7 | |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,320
|
Re: Holley 94 vacuum line fitting
Quote:
|
|
05-30-2019, 10:01 AM | #8 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,950
|
Re: Holley 94 vacuum line fitting
Thanks tubman. I learned something new.
Sounds like the product you mentioned would work. Here's a video about it. https://www.youtube.com/watch?v=zUI6GMkTOjU Last edited by 19Fordy; 05-30-2019 at 10:07 AM. |
05-30-2019, 11:18 AM | #9 |
Senior Member
Join Date: Jun 2010
Location: Detroit suburb, MI
Posts: 3,706
|
Re: Holley 94 vacuum line fitting
Or you can send "Charlie ny" a private message on the Barn and see if he has a spare bowl for your carb.
Sal |
|
|
Sponsored Links (Register now to hide all advertisements) |
|