|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
03-02-2014, 08:50 PM | #1 |
Senior Member
Join Date: May 2013
Location: Pa.
Posts: 2,174
|
?disconnect gas pedal from linkage?
Hopefully an easy one. I went to the search and found nothing. "35 How do you disconnect the gas pedal from the rest of the accelerator linkage ( just before it goes through the fire wall ). Looks like some kind of spring loaded setup. It's in good shape so I don't want to maniac it. The bolt to the floor pan was no prob but I can't figure out how to take it off the linkage as I want to remove the floor pan along with the trans access pan and the wood floor board on the passenger side to refurbish. I got the center trans access panel off and the passenger off but cant get the drive side pan off till I get the gas pedal removed?
Thx
__________________
Nomad |
03-02-2014, 08:57 PM | #2 |
Senior Member
Join Date: Jul 2012
Location: jacksonville,arkansas
Posts: 160
|
Re: ?disconnect gas pedal from linkage?
The spring is attached to a metal pin, it is pressed into the rubber on the pedal,maybe a Lil pb blaster and a twisting motion back in forth, the springs is available from macs I think that where mine came from as well as a new pedal, to put the pins ball ( you'll see what I mean when you get it off the pedal, I took a lil soap lubed the ball up and then stuck the pin in a nut driver and pushed it back in the socket. Hope this helps
|
Sponsored Links (Register now to hide all advertisements) |
|
03-02-2014, 09:02 PM | #3 |
Senior Member
Join Date: Jul 2011
Location: SF Bay Area
Posts: 6,648
|
Re: ?disconnect gas pedal from linkage?
delete
__________________
Alan |
03-02-2014, 09:07 PM | #4 |
Senior Member
Join Date: May 2010
Location: Above the gnat line in Georgia
Posts: 7,009
|
Re: ?disconnect gas pedal from linkage?
__________________
Life is like a roll of toilet paper. The closer to the end, the faster it goes. It is better to be seen, than viewed. "We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm". |
03-02-2014, 09:12 PM | #5 |
Senior Member
Join Date: May 2013
Location: Pa.
Posts: 2,174
|
Re: ?disconnect gas pedal from linkage?
Hi Thaplumbr, I was fixed on the aluminum connector closer to the firewall thinking the thinner rod connected to the pedal was part of the pedal set up.You'r indicating it's just a pressed pin going vertically through the rubber on the pedal which also goes through the metal linkage attaching it to the pedal all inside the rubber? Sorry I'm so dense.
Thx
__________________
Nomad |
03-02-2014, 09:14 PM | #6 |
Senior Member
Join Date: Jul 2011
Location: SF Bay Area
Posts: 6,648
|
Re: ?disconnect gas pedal from linkage?
Sponsored Links (Register now to hide all advertisements)
__________________
Alan |
03-02-2014, 09:35 PM | #7 | |
Senior Member
Join Date: Jul 2012
Location: jacksonville,arkansas
Posts: 160
|
Re: ?disconnect gas pedal from linkage?
Quote:
|
|
03-02-2014, 10:11 PM | #8 |
Senior Member
Join Date: May 2013
Location: Pa.
Posts: 2,174
|
Re: ?disconnect gas pedal from linkage?
Thx looked a little delicate didn't want to mangle it. A little info goes a long way. And yes I do enjoy a good cigar now and again! usually a R & J or an H. Upmann, also Arturo Fuente.
__________________
Nomad |
|
|
Sponsored Links (Register now to hide all advertisements) |
|