Rust-Oleum Appliance Epoxy Paint Warning

[Richard Lorenz]

This paint tends to blow out globules of paint along with the spray. I tried 2 different "serial numbers" from Walmart and also the Ace Hardware version of this paint. They usually start out O.K. but then start blowing the globules.

It is not worth the risk.

[H. L. Chauvin]

Hi Richard,

Thanks so much for taking your valuable time to report this Rust-Oleum paint failure information.

One can only imagine a similar case of the "REDS" accompanied by mental anguish, total frustration; e.g.:

1. Spend countless hours preparing Model A wire wheels for painting.

2. Spend hard earned cash for paint.

3. Begin painting and the paint exits the paint cans like a bad case of high pressure diarrhea.

4. Then, carefully removing very sticky Rust-Oleum epoxy diarrhea from one's Model A wire wheels.

5. Someone may be kind enough to mention another brand of epoxy paint, (perhaps with an Imodium formula, LOL), that works well .......... in order to benefit future serious Model A wheel painters.

[colin1928]

Only had these happen to me once turn out to be old cans that had sat around too long

[BILL WILLIAMSON]

Originally Posted by colin1928

Only had these happen to me once turn out to be old cans that had sat around too long

Most spray cans have an agitator ball" in it. Be SURE to take the time to shake it until you hear the BALL doing its' job!!! The ball "might" be stuck by the heavy pigment, that has settled to the BOTTOM! Sometimes, you need to BANG the can, to loosen it.
CLEAR cans, with NO pigments, usually don't have a ball.
Bill W.

[C26Pinelake]

usually only happens when you don't shake it enough. Shake required time and then another minute. Wayne

[H. L. Chauvin]

Sponsored Links (Register now to hide all advertisements)

After hearing Richard's terrible experience, it may help:

1. To first copy the Rust-Oleum cans' "serial numbers" prior to buying the Rust-Oleum paint; and,

2. Next call Rust-Oleum to ask for a "knowledgeable" paint technician ...... (from experience, most front desk people answering manufacturers' business phones today could care less if your can is either empty or loaded with Wasp Spray ); and,

3. Ask this technician if these serial numbers allows one to date the contents of the can; and if so,

4. Would he/she "highly" recommend using this particular can, "after" relating Richard's "horrible" experience with globules in the can.

5. Epoxy appliance paint may or may not have a specified shelf life accompanied with a record of not having a short turn over sales rate.

6. The spray painting "time" and hard work factor is always 99% of sweat for preparation and 1% of time spent in applying paint.

Hope this can help someone in the future.

[SeaSlugs]

epoxy paint may also be designed to be globulous, it gives it that textured look many appliances have. Kinda like the rustoleum hammered paint line.

unless it s literally painting like flicking a paint brush, I've had that due to the nozzles getting clogged and old paint.

[Dollar Bill]

Had the same exact thing happen to me. Fortunately, I was painting a panel for washer. Still frustrating to wash with thinner. Returned paint and purchased same from another store with no further problems. As Colin mentioned, I think it was simply old paint.

[d.]

spray cans to paint wheels?
powder coat is the preferred method, it lays down like glass and is very chip resistant.

[Synchro909]

Originally Posted by d.

spray cans to paint wheels?
powder coat is the preferred method, it lays down like glass and is very chip resistant.

The trouble with powder coating is that it fades. I have a car where there wheels were powdered the same colour as the car - as can be seen if I look at the inside of the centres. They are now a ridiculous looking orange/pink instead of burgundy.
As for rattle cans, the paint from those goes dull and grey in a short time. They're not for me.

[Mike V. Florida]

Look here,

http://www.mtfca.com/discus/messages...tml?1291854652

[BILL WILLIAMSON]

Sometimes, you can find nozzles that do a FAN shaped spray, instead of a FUNNEL shaped spray. They do a REALLY nice job.
When buying spray cans, ASK for extra nozzles, THEY'RE FREE!
Bill W.

[pgerhardt]

I just painted the underside of my running boards with Rust-Oleum Appliance epoxy paint with no problems. (I figure that fading will not be a problem since they will never see direct sunlight.)

[SwansEarlyFord]

Wow.

[ronn]

had this happen 3x at walmart- what I am guessing is that when they get large shipments, they are leaving them out and the paint gets funky in the cold.
buy my rustoleum elsewhere now and NO problems...............

[Mitch//pa]

Originally Posted by BILL WILLIAMSON

Sometimes, you can find nozzles that do a FAN shaped spray, instead of a FUNNEL shaped spray. They do a REALLY nice job.
When buying spray cans, ASK for extra nozzles, THEY'RE FREE!
Bill W.

I asked lowes for extra nozzles they looked at me like I was crazy maybe that's a perk for the west coasters

[Dale G.]

To stop the fading of powder coating, have the coater guy put a clear coat over your color. If you do not want the coating too thick, then use one coat of color and one coat of clear.

[Brian T]

Billy may have got lucky,--- asking a question like that in my neck of the woods is akin to having a battle of wits with an unarmed person.

[5window]

Rattle can paint doesn't have a hardener in it, so it won't hold up. Seen many appliances running down the road? Appliance paint is for indoors. Rustoleum never seems to stick well or flow for me-I much prefer Krylon for spray paint.