|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
09-16-2019, 03:55 PM | #1 |
Senior Member
Join Date: Jul 2019
Location: Southern Oregon
Posts: 782
|
Early V8 Dyno Work
I have read, with great interest, the work of Ted Eaton and his Y block, dyno tests.
Has anyone done anything like that with the first generation V8's? Or does anyone have any dyno runs on there own engines that they would like to share? Frank |
09-16-2019, 05:33 PM | #2 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Early V8 Dyno Work
There are several books out there on the topic. One is JWLs (who post often here on the Barn) book. Joe Abbin also has books out with dyno data.
|
Sponsored Links (Register now to hide all advertisements) |
|
09-16-2019, 06:13 PM | #3 |
Senior Member
Join Date: May 2010
Location: Charlotte NC KiWi-L100 available here
Posts: 2,963
|
Re: Early V8 Dyno Work
The Aussie Mike Davidson has books out with dyno info
|
09-16-2019, 06:21 PM | #4 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Early V8 Dyno Work
JWL says 400+ dyno runs, that should give you some ideas.
|
09-16-2019, 06:24 PM | #5 |
Senior Member
Join Date: May 2010
Location: Oshkosh, Wi
Posts: 4,527
|
Re: Early V8 Dyno Work
JWL's are real world tests.
|
09-16-2019, 09:41 PM | #6 |
Senior Member
Join Date: May 2010
Location: Chester Vt
Posts: 8,860
|
Re: Early V8 Dyno Work
Sponsored Links (Register now to hide all advertisements)
|
09-17-2019, 05:53 PM | #7 |
Senior Member
Join Date: Jul 2019
Location: Southern Oregon
Posts: 782
|
Re: Early V8 Dyno Work
I'll have to get JWL's book.
Can I assume that no one else has had their engine on a dyno (what about a chassis dyno), even to jet the carbs? |
09-17-2019, 06:33 PM | #8 | |
Senior Member
Join Date: Sep 2011
Location: Christchurch New Zealand
Posts: 1,611
|
Re: Early V8 Dyno Work
Quote:
Ended up going up 1 jet size on Main Jet, a single Stromberg 97 carb. Standard 81A engine 83 thou over. Edelbrock Heads. Dont have figures handy. Phil NZ Last edited by Phil Gillespie; 09-17-2019 at 08:38 PM. |
|
09-17-2019, 07:04 PM | #9 |
Senior Member
Join Date: May 2010
Location: Qld, Australia
Posts: 4,215
|
Re: Early V8 Dyno Work
Main jets size
Lawrie |
09-17-2019, 08:17 PM | #10 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Early V8 Dyno Work
I have recommended dyno tuning to several people who did so and liked the results.
|
09-18-2019, 05:24 PM | #11 |
Junior Member
Join Date: Jan 2016
Posts: 22
|
Re: Early V8 Dyno Work
Dave Tatom has done dyno runs on a blown flathead he races at Bonneville. He is in Mt Vernon, WA, and tests his flatheads, as well as other engines, in Renton, as I recall.
|
11-30-2019, 12:26 PM | #12 |
Senior Member
Join Date: Nov 2012
Location: Central Texas
Posts: 155
|
Re: Early V8 Dyno Work
I have dyno tested several Ford Flathead V8's. The standard build for a street Flattie will make 150 HP while an all out build (normally aspirated) will break the 200 HP mark. I did dyno a blown Flat Head V8 for an old school dragster that made in excess of 450 HP but that engine was set up on 'Kill'. Ted Eaton.
|
11-30-2019, 01:11 PM | #13 |
Senior Member
Join Date: Jul 2019
Location: Southern Oregon
Posts: 782
|
Re: Early V8 Dyno Work
Thank you, very much, Ted. Are those dyno results posted somewhere on your web site?
If not, could you give general specs for a 150 HP and a 200 hp build? Such as, cubic inch, approx C/R, cam and carburation?
__________________
Frank '35 Ford Model 51 '48 Ford F3 '54 Ford Tudor Mainline |
11-30-2019, 01:20 PM | #14 |
Senior Member
Join Date: Jul 2019
Location: Southern Oregon
Posts: 782
|
Re: Early V8 Dyno Work
Oh, one other thing, did the ignition timing vary much between the 150 and 200 hp versions?
__________________
Frank '35 Ford Model 51 '48 Ford F3 '54 Ford Tudor Mainline |
11-30-2019, 01:51 PM | #15 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,319
|
Re: Early V8 Dyno Work
|
11-30-2019, 02:15 PM | #16 | |
Senior Member
Join Date: Dec 2010
Location: East Coast in CT
Posts: 1,529
|
Re: Early V8 Dyno Work
Quote:
I have had my engines on the rear wheel dyno a number of times however the results must remain a secret. All I can say is more than one HP per cube at the wheels and over 200 MPH on the race surface. Very valuable for getting a good jetting tune up. Ronnieroadster
__________________
I use the F word a lot no not that word these words Flathead , Focus and Finish. "Life Member of the Bonneville 200 MPH Club using a Ford Flathead block" Owner , Builder, Driver of the First Ford Flathead bodied roadster to run 200 MPH Record July 13, 2018 LTA timing association 200.921 in one and a half miles burning gasoline. First ever gas burning Ford flathead powered roadster to run 200 MPH at Bonneville Salt Flats setting the record August 7th 2021 at 205.744 MPH |
|
11-30-2019, 04:26 PM | #17 |
Senior Member
Join Date: May 2010
Location: Chester Vt
Posts: 8,860
|
Re: Early V8 Dyno Work
I doubt that anyone has reached the 200 hp mark with a normally aspirated flathead. using regular gas (91/93 oct). The reason I say this, is: the ports wont pass enough air. They come close but at around 48/6000 RPM depending on displacement, the ports shut dowm. I built a 294 blown engine for Ron Horrell to replace the 296 engine I build 15 years ago. Using a Magnason /Eaton blower his engine produced 235 HP ay 4500 red line. With 5 lbs of boost. It also produced 300 ft /lbs or torque at 3000 rpm with 3 pounds of boost. I would suggest that if anyone makes a new block he work on the intake port allot. Must get rid of the bowl.
A garden hose will only pass so much water, with mother nature pushing on it. |
11-30-2019, 05:17 PM | #18 |
Senior Member
Join Date: May 2010
Location: Qld, Australia
Posts: 4,215
|
Re: Early V8 Dyno Work
the engine in our dragster is 276, 4/71 blower at 13 lbs ,home made heads ,has run 9.3 at 141 mph , with the weight of the dragster we think about 350hp.
Lawrie |
11-30-2019, 05:34 PM | #19 | |
Senior Member
Join Date: Dec 2010
Location: East Coast in CT
Posts: 1,529
|
Re: Early V8 Dyno Work
Quote:
Ronnieroadster
__________________
I use the F word a lot no not that word these words Flathead , Focus and Finish. "Life Member of the Bonneville 200 MPH Club using a Ford Flathead block" Owner , Builder, Driver of the First Ford Flathead bodied roadster to run 200 MPH Record July 13, 2018 LTA timing association 200.921 in one and a half miles burning gasoline. First ever gas burning Ford flathead powered roadster to run 200 MPH at Bonneville Salt Flats setting the record August 7th 2021 at 205.744 MPH |
|
12-01-2019, 05:05 PM | #20 | |
Senior Member
Join Date: Nov 2012
Location: Central Texas
Posts: 155
|
Re: Early V8 Dyno Work
Quote:
Because the Eaton Balancing website concentrates heavily on the Ford Y-Block builds, other engine builds are not posted on that site. I can see why there's not a lot of engine dyno information out there for the Ford Flat head V8 engines. They are not the easiest engine to get hooked up to an engine dyno so many of the dyno shops out there will not set up for them. The 450 HP supercharged Flathead was on nitro methane and serious boost. That one made everyone's eyes water as it was running zoomies and the shop was getting a full blast of burnt nitro fuel. It was a solid 9 second runner in the quarter mile. The 200+HP normally aspirated Flathead was a Bonneville engine that was just breaking the 200 HP mark at 203-205 HP. That particular engine was 294 cubic inches at 10.1:1 compression ratio and was running on 110 octane racing gasoline with a Hogan's sheet metal intake manifold and a pair of 390 cfm 4V Holley carbs. Camshaft was a Potvin 425. The piston design required that the Offenhauser heads be machined accordingly for piston clearance in the cylinder heads. The combustion chamber cc's are 73.6 while the piston domes are 25 cc's. Exhaust header design was also critical on that particular engine. Without looking it up, I vaguely remember it running at 24° total timing for the best horsepower numbers. Tried to post pictures of the pistons and combustion chambers but this site asks for URL links which I don't have. I'd have to look at the build details for the 150 HP version for the Flattie but remember it having Edelbrock heads, Offenhauser two deuce intake with new Speedway carbs, the small Isky camshaft, and Fenton cast iron headers. Final cubic inch on that one escapes me right now. Compression ratio on that one was for pump gas premium and idled nicely. Higher horsepower versions than this one have been done but those get ragged for running as everyday street engines without a large gain in horsepower. Ted Eaton. |
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|