|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
|
10-16-2016, 09:22 PM | #1 |
Senior Member
Join Date: Jun 2011
Location: South Dakota
Posts: 405
|
How I pinstriped my 33 Tudor
I did the pinstriping on my 33 Tudor this weekend. I could not find a similar process description in other posts and thought that those planning to do the same job will find the comments helpful.
It seems restorers usually do the job using a special brush to apply enamel pinstriping paint. Apparently the most common paint brand in the USA is OneShot. I quickly discarded the idea because I had to mix colors to obtain the Tacoma Cream needed for my car and I am totally clueless on how to do that. OneShot is sold in all base colors but no information on which ones to mix to obtain the needed color and after visiting several paint shops with this question I could not get an answer. My next option was to use the same paint that I have already used to paint my wheels. It is a PolyUrethane-based Tacoma Cream color and I have enough left after I did my wheels several months ago. It is not as thick as enamel and not good to apply with brush so I asked my painter for help and he was willing to come over the weekend with his spray gun and compressor to work with me to finish this job. I have a kit of Pinstriping stencils from a company kwown as Finesse www.finessepinstriping.com . This company sells stencils with the Pinstripes pattern for every classic american car. I bought kit F-43 which has 3 adhesives stencils covered by a transparent layer. The stencils are separated so that they will let you paint two 1/32 inches stripes separated by 3/32 inches between them, just as the original pattern. You can use a brush to apply the paint or a spray gun as I did. First step is to clean the area well and gently sand the clear coat with 2000 grit just enough to favour adherence of the new paint. Then apply the Finesse stripe with no interruptions all around the car beginning on one end of the hood. On the gaps between hood and cowl and on the door gaps you just keep covering with the tape to make sure there is a continuous sharp line all around the car. Next 4 photos show this process. The most difficult part is to cut the middle stencil to create a spear-shaped end on the front end of the hood. I had practice several times before I was happy with it. Then I removed the clear cover leaving the 3 stencils attached to the car as shown in this photo. Next begins the masking process to protect the rest of the paint from accidentally being sprayed. I put enought newspaper around that you can read the entire news just walking around my car! My painter applying PU Tacoma cream. Waited about an hour and applied a couple of layers of clear coat and then removed all the masking paper. Here we start removing the masking tape on the edges of the Finesse striping. Removing the top masking tape leaving the 3 stencils still attached and now painted. Next the top and the bottom stencils removed and here I am removing the center stencil to leave the pin striping visible. Edges in gaps are very sharp This is how the ends look like at the front of the hood, to me this was the most difficult part The R side not as even line as the L but still very acceptable. And this is how the final job looks like. I am totally happy with it. It took an entire day, two of us, very tedious preparation and application of the Finesse stripe. Everything depends on it so you better get a lot of patience, cool drinks, good weather, no interruptions, etc, etc and it will look just like original. If you have a steady hand for a brush AND you got the right color in enamel paint probably will be as good. Others may have different approaches, I just wanted to show in a single post the way of doing it with the Finesse stripes plus a spray gun. Manuel |
10-16-2016, 09:38 PM | #2 |
Senior Member
Join Date: May 2015
Posts: 8,183
|
Re: How I pinstriped my 33 Tudor
What about the stripes on the louvers on the hood sides? Same process? Same day?....
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
Sponsored Links (Register now to hide all advertisements) |
|
10-16-2016, 09:49 PM | #3 |
Senior Member
Join Date: May 2010
Location: Above the gnat line in Georgia
Posts: 7,009
|
Re: How I pinstriped my 33 Tudor
It appears in several places that when removing the strips of the stencil the paint lifted off as well, leaving a chipped appearance. Any way of preventing that?
__________________
Life is like a roll of toilet paper. The closer to the end, the faster it goes. It is better to be seen, than viewed. "We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm". |
10-17-2016, 11:42 AM | #4 | |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,115
|
Re: How I pinstriped my 33 Tudor
Quote:
I think this job came-out beautiully on the Doctor's car....time and effort well-spent! DD |
|
10-17-2016, 01:18 PM | #5 |
Senior Member
Join Date: May 2010
Location: Above the gnat line in Georgia
Posts: 7,009
|
Re: How I pinstriped my 33 Tudor
Left cowl appears to have some lift off in the area of the short strip on the belt molding. Not much, but very noticeable to me anyhow. A couple of other small places as well. Just saying. Really a nice job over all.
__________________
Life is like a roll of toilet paper. The closer to the end, the faster it goes. It is better to be seen, than viewed. "We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm". |
10-17-2016, 03:02 PM | #6 |
Senior Member
Join Date: Sep 2013
Location: Florida
Posts: 588
|
Re: How I pinstriped my 33 Tudor
Sponsored Links (Register now to hide all advertisements)
__________________
Do I look like I have a plan B? |
10-19-2016, 02:23 AM | #7 |
Senior Member
|
Re: How I pinstriped my 33 Tudor
To keep from lifting the stripe gently pull the tape at low angle away and back. I use model car paint and use regular masking tape. Tape the car completely, cut the tape at each panel, use a striping brush, do one panel at a time, pull off the tape as soon as you stripe a panel before going to the next panel. Doing it that way the paint will flow and not leave a rough edge. Practice a little on something and you will see how it works.
|
10-16-2016, 10:18 PM | #8 |
BANNED
Join Date: May 2010
Location: Sonoma,Calif.
Posts: 877
|
Re: How I pinstriped my 33 Tudor
Great job. You should be proud of your work.
|
10-16-2016, 10:31 PM | #9 |
Senior Member
Join Date: May 2010
Location: Kokomo, Indiana
Posts: 1,731
|
Re: How I pinstriped my 33 Tudor
Nice job and a great looking car!
__________________
Henry |
10-16-2016, 11:43 PM | #10 |
Senior Member
Join Date: May 2010
Location: Qld, Australia
Posts: 4,223
|
Re: How I pinstriped my 33 Tudor
Manual, I did mine with the small brush that came with the kit,turned out great.
Lawrie |
10-17-2016, 06:54 AM | #11 |
Senior Member
Join Date: May 2010
Posts: 13,700
|
Re: How I pinstriped my 33 Tudor
What is the price of that kit?
|
10-17-2016, 07:53 AM | #12 |
Senior Member
Join Date: May 2010
Location: Hampshire, Illinois
Posts: 392
|
Re: How I pinstriped my 33 Tudor
Wow, great job!
You must have a lot of patience. Bob-Hampshire, Ill. |
10-17-2016, 08:59 AM | #13 |
Senior Member
Join Date: Sep 2016
Location: Geneseo, IL
Posts: 290
|
Re: How I pinstriped my 33 Tudor
According to the Finesse website, $10.29 (plus shipping to Paraguay, in Manuel's case)
__________________
Regards, Scott '47 Mercury Convertible '25 Dodge Bros. Touring Car '63 MG Midget |
10-17-2016, 08:36 AM | #14 |
Senior Member
Join Date: Apr 2011
Location: Northern New Jersey
Posts: 370
|
Re: How I pinstriped my 33 Tudor
PS. don't forget to remove the rear spare tire
__________________
Assumption is the mother of all foul-ups. |
10-17-2016, 09:01 AM | #15 |
Senior Member
Join Date: May 2010
Location: Oakmont, Pa (Longwood)
Posts: 297
|
Re: How I pinstriped my 33 Tudor
nice job, I paid for mine, darn it.
|
10-17-2016, 10:13 AM | #16 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,443
|
Re: How I pinstriped my 33 Tudor
It looks good. This tape looks like it sets down well with minimum bleed through. The type of tape used is critical on striping, especially if you have to lightly abrade the surface to get it to stick such as when striping over an older paint job. Bleed through is a product of tape that doesn't stick down well enough or is affected by cleaning solvents. How a person pulls the masking tape can affect the striping a lot. I pull it right after the final coat so it is still tacky and can flow enough to level out a bit more. I pull straight back on the tape to eliminate the stringing of paint that can happen sometimes. It takes a steady hand and a lot of concentration to get it right.
I caution folks about using newsprint as a mask. The paper is drawn through machines that perforates it with little grabber teeth in several places. I recommend using regular masking paper if you can get it. It's well worth the price and can save a lot of grief. Last edited by rotorwrench; 10-17-2016 at 05:28 PM. Reason: change tape to paper |
10-17-2016, 02:09 PM | #17 |
Senior Member
|
Re: How I pinstriped my 33 Tudor
Nice job
|
10-17-2016, 02:25 PM | #18 |
Senior Member
Join Date: May 2010
Location: Mn
Posts: 2,411
|
Re: How I pinstriped my 33 Tudor
When removing the tape from the new pinstripe, do NOT pull upwards, as you have
a chance of leaving an un-clean edge or even lifting the pinstripe edge up with the tape. Pull the tape at a very low angle towards you, it has a better chance of leaving a clean edge. Sorry this picture is not very good, but hope you can see the angle to pull the tape Click on picture to Enlarge.
__________________
If mama ain't happy, ain't nobody happy. But if daddy ain't happy...RUN |
10-17-2016, 03:21 PM | #19 |
Senior Member
Join Date: Oct 2015
Location: Forest, Virginia
Posts: 250
|
Re: How I pinstriped my 33 Tudor
If you spray stripes an enamel based color can be shot with a small fingertip gun, thinned with lacquer thinner and the tape pulled while the paint is still tacky. Not quite tacked over enamel will NOT leave an edge you can feel when the tape is pulled at this time. Pull the tape back over itself in a line even with it's application. Gary P. S. Great Looking Car!
__________________
Just Passin' Thru.....Slowly! |
10-17-2016, 04:59 PM | #20 |
Senior Member
Join Date: May 2010
Location: Colorado
Posts: 553
|
Re: How I pinstriped my 33 Tudor
Excellent write-up, and great results. This looks like a good way to stripe without having an expensive striper do it.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|