|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
04-20-2021, 06:20 PM | #1 |
Senior Member
Join Date: Nov 2012
Posts: 327
|
'35 backing plate bolts
Has anyone found a good way to remove these bolts. The head is a bit bigger than 11/16 and difficult to get any kind of wrench inside the grease baffle. It wants to turn with the nut and I can't get a grip. They seem to be rounded in all the wrong places.
Thanks for any ideas that might work. Last edited by 15max; 04-20-2021 at 06:21 PM. Reason: Need capitol letter |
04-20-2021, 08:45 PM | #2 |
Senior Member
Join Date: May 2010
Location: Minnesota
Posts: 1,138
|
Re: '35 backing plate bolts
I would recommend that you power wash the area to get rid of all of the grease. Then use a torch to heat up the nuts on the other side and hold the square end with a vice grip plier. Hope that helps.
|
Sponsored Links (Register now to hide all advertisements) |
|
04-20-2021, 10:38 PM | #3 |
Senior Member
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,574
|
Re: '35 backing plate bolts
I have an old 3/4" open end wrench that I bent to a kinda Z shape to hold them. These bolts can fight, best to make the effort to get all residue from the cotter pins out first, then lube it all up good. There is a "lock" tang too, so keep it tight against the backing plate to keep the tang engaged
|
04-20-2021, 10:58 PM | #4 |
Senior Member
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,834
|
Re: '35 backing plate bolts
Mart on here made a special tool that holds all 4 heads, probably more effective when re-fitting them.
__________________
Unfortunately, two half wits don't make a whole wit! |
04-20-2021, 11:22 PM | #5 |
Senior Member
Join Date: May 2012
Location: Queensland, Australia
Posts: 10,370
|
Re: '35 backing plate bolts
Hard to get to Square Head Bolts on Backing Plate and handy "home-made" Tool to reach them. |
04-20-2021, 11:57 PM | #6 |
Senior Member
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,574
|
Re: '35 backing plate bolts
Sponsored Links (Register now to hide all advertisements)
|
04-21-2021, 02:16 AM | #7 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,754
|
Re: '35 backing plate bolts
If you can get a ring of steel like a big washer and put it over the heads of the bolts, and then refit the hub so it clamps the bolts tight against the axle casing it will hold the heads in place while the nuts are removed.
A ring of plywood would probably do it. Mart. |
04-21-2021, 05:07 AM | #8 |
Senior Member
Join Date: Jul 2016
Location: Lake worth Florida
Posts: 1,100
|
Re: '35 backing plate bolts
I bent a inexpensive open end wrench .
|
04-21-2021, 11:10 AM | #9 |
Senior Member
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,574
|
Re: '35 backing plate bolts
Good idea mart ^^^ clamping the heads in place would help
|
04-21-2021, 12:52 PM | #10 |
Senior Member
Join Date: Jul 2016
Location: Lake worth Florida
Posts: 1,100
|
Re: '35 backing plate bolts
I forgot , i had first used a flat gasket scraper and a screwdriver. I just placed the flat blade between the flat on the bolt and the spindle back. It worked on all but one that had been replaced with a standard 6 sided bolt .
|
04-22-2021, 10:01 AM | #11 |
Senior Member
Join Date: Nov 2012
Posts: 327
|
Re: '35 backing plate bolts
Thanks for all the kind responses. I tried the vise grips, bent wrench and several wedges with no success. Finally I made this plate to fit the head. It required a spacer to hold it against the bolt and even a large C-clamp to keep it tight. However, the nuts still would not budge until they were heated as mentioned by Gary.
One more ordeal. It certainly was satisfying when they came loose. |
04-22-2021, 10:58 AM | #12 |
Senior Member
Join Date: Jul 2016
Location: Lake worth Florida
Posts: 1,100
|
Re: '35 backing plate bolts
Nice going ! I replaced thoe with later T bolts
|
04-22-2021, 11:49 AM | #13 |
Senior Member
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,574
|
Re: '35 backing plate bolts
Nice job !
|
04-22-2021, 12:29 PM | #14 | |
Junior Member
Join Date: Aug 2014
Posts: 13
|
Re: '35 backing plate bolts
Quote:
|
|
04-22-2021, 01:26 PM | #15 |
Senior Member
Join Date: Nov 2012
Posts: 327
|
Re: '35 backing plate bolts
Thanks guys
Replaced with later T bolts would be the kind thing to do wouldn't it? |
04-22-2021, 03:02 PM | #16 |
Member
Join Date: Sep 2017
Location: Venetia, Pa.
Posts: 51
|
Re: '35 backing plate bolts
That's a nice tool. Feel like making some more?
|
04-22-2021, 04:21 PM | #17 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: '35 backing plate bolts
Cool tool!
|
04-24-2021, 10:32 AM | #18 |
Senior Member
Join Date: Nov 2012
Posts: 327
|
Re: '35 backing plate bolts
I don't think so. While it is a simple thing to make it took me 5 hours with a hacksaw, files and a drill. A well equipped machine shop might be able to make them cheaper that I could. I could provide drawings if anyone is interested. Had I applied heat earlier the simpler tools should have worked as well.
Thanks |
04-25-2021, 03:30 PM | #19 |
Senior Member
|
Re: '35 backing plate bolts
I have used Ggmac s idea before the day ,
|
04-26-2021, 10:46 AM | #20 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,944
|
Re: '35 backing plate bolts
Replace the stock bolts with Grade 8 1/2-20 SAE bolts. The hex head will provide a "wrenching" surface. Or you could tack weld a nut to the head of the OEM bolt.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|