![]() |
#41 | |
Senior Member
Join Date: May 2010
Location: Yakima Washington
Posts: 913
|
![]() Quote:
The filler pipe is not a pipe thread. The fuel line is not a pipe thread. It is sealed with a compression ferrule. So the only place to use sealer is on the drain plug. Bill |
|
![]() |
![]() |
![]() |
#42 |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 9,082
|
![]() |
![]() |
![]() |
Sponsored Links (Register now to hide all advertisements) |
|
![]() |
#43 |
Senior Member
Join Date: May 2010
Location: Irving, Texas
Posts: 598
|
![]() |
![]() |
![]() |
![]() |
#44 |
Senior Member
Join Date: Jun 2010
Location: St Croix Falls WI
Posts: 2,080
|
![]()
D'ya suppose the MESS above could have been avoided by simply asking " should I use some type of sealant on the drain plug threads on my 40 Ford gas tank " ? Most folks would not refer to the drain plug as a "fitting that goes to into the gas tank" . The one clear bit of info from the poster of this thread simply states "40 ford" & it was correctly pointed out that a 40 ford only has a plug - NOT a "fitting" or a "shutoff valve" . The thread was-is not about 32 trucks . If you wanna be the top bananna start your own thread . Also snipping at Bruce Lancaster falls into the bad idea category with me as he is probably one of the most knowledgeable contributers here . HEY RYAN !!!!! I would cast a vote to get rid of this mess of a thread .
|
![]() |
![]() |
![]() |
#45 |
Member Emeritus
Join Date: May 2010
Location: Madison, NJ
Posts: 5,230
|
![]()
Drain plug and not the fuel line?? THAT was a touch unclear! He's in luck, though, as 99% of the things won't come out without using nuclear weapons...he's miles ahead if he needs info on putting it back in!
|
![]() |
![]() |
![]() |
#46 |
Member
Join Date: Dec 2010
Location: pittsburgh, Pa.
Posts: 64
|
![]() Sponsored Links (Register now to hide all advertisements)
__________________
The only thing that can beat an attempt----is a failure!!!! |
![]() |
![]() |
![]() |
#47 |
Senior Member
Join Date: Oct 2010
Location: Mantua, Ohio
Posts: 269
|
![]()
Last time for me. Pipe dope on pipe threads (optional). No dope on any other fuel line fittings, no matter what kind of vehicle. Compression or even flare seal at the compression or the flare, not the threads. How did this get so far?
|
![]() |
![]() |
![]() |
#48 |
Member Emeritus
Join Date: May 2010
Location: Madison, NJ
Posts: 5,230
|
![]()
Damn right! I wish someone had put pipe dope on all of my Ford drainplugs 80 years ago.
The progress towards the actual question reminds me of the threads that start something like "I have a flathead. How do I fix the carburetor?" AAAAAAH! How many electrons have died in vain! |
![]() |
![]() |
![]() |
#49 |
Senior Member
Join Date: May 2010
Posts: 820
|
![]() |
![]() |
![]() |
![]() |
#50 | |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 9,082
|
![]() Quote:
|
|
![]() |
![]() |
![]() |
#51 |
Senior Member
Join Date: May 2010
Location: Windham, CT
Posts: 702
|
![]()
Well I just read through this for the first time today because I couldn't see how such a simple question could go on for three pages. I thought maybe the subject had changed to the meaning of life. LOL
Now I'm adding to it.
__________________
[FONT=Comic Sans MS] |
![]() |
![]() |
![]() |
#52 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,803
|
![]()
Maybe for all of us it is a lesson in how to ask a question clearly, without leaving out essential details or over embellishing the facts.
In my background (automotive engineering - development) you have to know how to clearly phrase a question. Mart. |
![]() |
![]() |
![]() |
#53 |
Senior Member
Join Date: May 2010
Location: warwick Rhode Island
Posts: 464
|
![]()
Im sorry my question was so difficult, and that i'm not an engineer just an OLD MAN trying his best to put this old Ford back together, but for those that asked ; it does say at the subject matter that it is for a" fuel line" i'll admit i did forget to say it was for a 1940 Ford.
|
![]() |
![]() |
![]() |
#54 |
Senior Member
Join Date: May 2010
Location: warwick Rhode Island
Posts: 464
|
![]()
While i'm being "Lambasted" i might as well ask another dumb question. Does anyone know what the purpose of the spring on the installation of the fuel tank, ""ON A 1940 FORD""
|
![]() |
![]() |
![]() |
#55 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,803
|
![]()
Sorry, Hope, I was not criticising you. You did exactly the right thing. You asked a question and got the answer.
Hope the rest of the re-build goes well. Mart. |
![]() |
![]() |
![]() |
#56 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,803
|
![]()
Ok here's my take on the spring. It is to allow some frame flex (lots of un-paved roads back in the day) without transmitting that flex through to the tank. Radiators are mounted with a spring for the same reason.
Mart. |
![]() |
![]() |
![]() |
#57 |
Senior Member
Join Date: May 2010
Location: warwick Rhode Island
Posts: 464
|
![]()
Thank you
|
![]() |
![]() |
![]() |
#58 | |
Senior Member
Join Date: May 2010
Posts: 820
|
![]() Quote:
![]() |
|
![]() |
![]() |
![]() |
#59 |
Senior Member
Join Date: May 2010
Posts: 820
|
![]()
I see you got the answer .
![]() |
![]() |
![]() |
![]() |
#60 |
Senior Member
Join Date: May 2010
Location: warwick Rhode Island
Posts: 464
|
![]()
isn't funny how a simple question can be turned around so much, to make it sound stupid by some a....
|
![]() |
![]() |
![]() |
|
|
Sponsored Links (Register now to hide all advertisements) |
|