|
Sponsored Links (Register now to hide all advertisements) |
|
![]() |
![]() |
Thread Tools | Display Modes |
![]() |
#1 |
Senior Member
Join Date: Aug 2021
Location: Upstate N.Y.
Posts: 455
|
![]()
Hello.
On a 35/36’ Coupe , the bumper brackets bolt on the corner of the frame. Then set body down on frame . A 3/8” - 24 body mount bolt goes up through this bracket. Approx how thick is the pad that goes between body and bracket ? T/Y |
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: Aug 2021
Location: Upstate N.Y.
Posts: 455
|
![]() |
![]() |
![]() |
Sponsored Links (Register now to hide all advertisements) |
|
![]() |
#3 |
Senior Member
Join Date: May 2010
Posts: 4,803
|
![]()
There are some photos below of the corner brackets. Between the body and the corner brackets, at the rear, on the 35, are square washers with a hole for the bumper arm bolt. The amount of these washers depends upon the distance between the brackets and the body. Usually a couple.
|
![]() |
![]() |
![]() |
#4 |
Senior Member
Join Date: Aug 2021
Location: Upstate N.Y.
Posts: 455
|
![]()
Terry, thank you.
I just found a diagram that shows 2 1/2” pad for rear mount . Stretch |
![]() |
![]() |
![]() |
#5 |
Senior Member
Join Date: Aug 2021
Location: Upstate N.Y.
Posts: 455
|
![]() |
![]() |
![]() |
![]() |
#6 | |
Senior Member
Join Date: May 2015
Posts: 8,592
|
![]() Sponsored Links (Register now to hide all advertisements)
Quote:
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
![]() |
![]() |
![]() |
#7 | |
Senior Member
Join Date: May 2015
Posts: 8,592
|
![]() Quote:
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
![]() |
![]() |
![]() |
#8 | |
Senior Member
Join Date: May 2015
Posts: 8,592
|
![]() Quote:
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
![]() |
![]() |
![]() |
#9 |
Senior Member
Join Date: Jul 2011
Location: Alvaton, Kentucky, USA
Posts: 962
|
![]()
Could you post the part number & vendor for those pads ? Can't read the diagrams when I enlarge the pic.
Thanks, Bob |
![]() |
![]() |
![]() |
#10 |
Senior Member
Join Date: Aug 2021
Location: Upstate N.Y.
Posts: 455
|
![]() |
![]() |
![]() |
![]() |
#11 | |
Senior Member
Join Date: May 2015
Posts: 8,592
|
![]() Quote:
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
![]() |
![]() |
![]() |
#12 |
Senior Member
Join Date: Jul 2011
Location: Alvaton, Kentucky, USA
Posts: 962
|
![]()
Thank you !
|
![]() |
![]() |
![]() |
#13 |
Senior Member
Join Date: Jul 2011
Location: Alvaton, Kentucky, USA
Posts: 962
|
![]()
Thank you !
|
![]() |
![]() |
![]() |
#14 |
Senior Member
Join Date: Aug 2021
Location: Upstate N.Y.
Posts: 455
|
![]()
Unfortunately today I posted here in our “Parts Wanted” section.
The metal channel that goes in Roof insert area. Weird that is missing on our 3W coupe. Last edited by ssffnomad; 04-03-2024 at 10:20 PM. |
![]() |
![]() |
![]() |
#15 |
Senior Member
Join Date: Aug 2021
Location: Upstate N.Y.
Posts: 455
|
![]()
Good Morning.
So are looking way ahead, and trying to source interior parts. Can only find one company that can provide a 36’ 3W pre sewn headliner. “Acme Auto Headlining Co.” Long Beach, CA Have any of you guys dealt with them ? Thanks Stretch |
![]() |
![]() |
![]() |
#16 |
Senior Member
Join Date: May 2010
Location: Napa,California
Posts: 6,097
|
![]()
Acme is a very old company and have probably been around since the 50's. Never heard any negatives on them. Right now they are probably the only game in the hobby.
|
![]() |
![]() |
![]() |
#17 |
Senior Member
Join Date: Aug 2021
Location: Upstate N.Y.
Posts: 455
|
![]()
IMG_1666.jpg
IMG_1668.jpgHello. Headliner questions . I have two Bowes , is that correct ? There are two screws for Bowes , what’s the hole above them for ? Thanks Guys. Stretch |
![]() |
![]() |
![]() |
#18 | |
Senior Member
Join Date: May 2015
Posts: 8,592
|
![]() Quote:
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
![]() |
![]() |
![]() |
|
|
Sponsored Links (Register now to hide all advertisements) |
|