![]() |
#1 |
Junior Member
Join Date: Jul 2021
Location: Springfield, MO
Posts: 24
|
![]()
Have a bit on a dilemma. Bought a 1936 Ford Pickup years ago and am just now starting to reassemble. The truck appeared to be complete, except no engine/transmission. However, I have come to realize that the rear fenders may not be the correct year. Attached is a photo. The overall arc length measured on the outside of the fender is about 68-1/2"; Width = 10-1/2"; Horizontal front to back length of 45". Went to a car show this weekend and saw a '35 that had a bolt to a rear fender bracket. Mine have no similar bolt attachment location.
So, what are these? 1934? |
![]() |
![]() |
![]() |
#2 | |
Senior Member
Join Date: May 2015
Posts: 10,143
|
![]() Quote:
|
|
![]() |
![]() |
Sponsored Links (Register now to hide all advertisements) |
|
![]() |
#3 |
Senior Member
Join Date: May 2010
Location: Above the gnat line in Georgia
Posts: 7,082
|
![]()
Certainly not 35-37. Maybe 32?
__________________
Life is like a roll of toilet paper. The closer to the end, the faster it goes. It is better to be seen, than viewed. "We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm". |
![]() |
![]() |
![]() |
#4 |
Senior Member
Join Date: Jul 2013
Location: Wisconsin
Posts: 228
|
![]()
Almost looks to me like 30/31 Model A pickup rear fender.
Pat |
![]() |
![]() |
![]() |
#5 |
Senior Member
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,599
|
![]()
Not '32 as the hole spacing where it attaches to the chassis frame in front is too wide.
|
![]() |
![]() |
![]() |
#6 |
Senior Member
Join Date: May 2010
Location: Southern France
Posts: 5,832
|
![]() Sponsored Links (Register now to hide all advertisements)
|
![]() |
![]() |
![]() |
#7 |
Senior Member
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,599
|
![]()
I agree that it is likely the '33-'34 version, but it's the hole spacing that suggests that as the '32 also has two holes where the fender attaches to the frame as shown below in the photos of a NOS '32 fender.
|
![]() |
![]() |
![]() |
#8 |
Senior Member
Join Date: May 2012
Location: Queensland, Australia
Posts: 12,007
|
![]() NOS 1932 Ford Rear Fenders - DavidG |
![]() |
![]() |
![]() |
#9 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 1,537
|
![]()
Nottaford. Likely Cornbinder.
(Not a Ford. Likely International pickup) |
![]() |
![]() |
![]() |
#10 |
Junior Member
Join Date: Jul 2021
Location: Springfield, MO
Posts: 24
|
![]()
Still looking for some consensus on these fenders. Here are a couple more photos.
Front of the fender has one level of 3 holes on 3-1/2" centers and a lower level of 2 holes on 5" centers. Assume the two hole pattern was added to bolt to the '36 running boards. Second photo shows fender to vehicle bolt pattern. Note that previous owner likely added holes and attached fenders using original carriage type bolts that went through the truck box. |
![]() |
![]() |
![]() |
#11 | |
Senior Member
Join Date: May 2015
Posts: 10,143
|
![]() Quote:
|
|
![]() |
![]() |
![]() |
#12 |
Junior Member
Join Date: Jul 2021
Location: Springfield, MO
Posts: 24
|
![]()
Well, they'd probably be worth more if they were from a Binder.
|
![]() |
![]() |
![]() |
#13 |
Senior Member
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,599
|
![]()
With these additional photos, I agree with Karl that they are not Ford fenders.
|
![]() |
![]() |
![]() |
|
|
Sponsored Links (Register now to hide all advertisements) |
|