Rotor position at TDC

[fried okra]

I swapped out the distributor on my '31 Tudor 12v engine.

Next I was gonna set the timing using the Nu-Rex tool. I am visibly at TDC on #1 piston and get a slight motion on the timing pin against the timing gear but it does not readily go into the timing gear hole. I assume the timing pin is just too tight a fit.

Anyway, I was expecting to see the rotor at the #1 cylinder pin in the distributor cap. Instead the rotor is 180 off from where I expected it to be.

Is this rotor position normal or am I missing something?

[ModelA29]

You dropped the distributor in 180 degrees out of sync. Lift it up and spin the rotor to #1 cylinder and drop it back in.

[Y-Blockhead]

Originally Posted by ModelA29

You dropped the distributor in 180 degrees out of sync. Lift it up and spin the rotor to #1 cylinder and drop it back in.

Nope. The slot on the bottom of the distributor is offset. The distributor will only drop down into the slot in one position. If he is 180° off he will have to loosen the rotor and turn just the rotor 180° to line up with TDC on #1 compression stroke. No need to lift the distributor.

[brokenspoke]

Originally Posted by y-blockhead

nope. The slot on the bottom of the distributor is offset. The distributor will only drop down into the slot in one position. If he is 180° off he will have to loosen the rotor and turn just the rotor 180° to line up with tdc on #1 compression stroke. No need to lift the distributor.

bingo

[JayJay]

Originally Posted by Y-Blockhead

Nope. The slot on the bottom of the distributor is offset. The distributor will only drop down into the slot in one position. If he is 180° off he will have to loosen the rotor and turn just the rotor 180° to line up with TDC on #1 compression stroke. No need to lift the distributor.

I believe OP stated he was using the NuRex tool. If so it's pretty much foolproof. At #1 TDC compression you loosen the distributor cam, rotate the cam a couple of times, stop with the tool resting against the #4 terminal, then tighten the cam.

[Y-Blockhead]

Sponsored Links (Register now to hide all advertisements)

Originally Posted by ModelA29

You can lift it anywhere and turn it 180 degrees so it drops back into the drive slot. When the pin is in the dimple it's always at TDC.

Originally Posted by Y-Blockhead

Nope. The slot on the bottom of the distributor is offset. The distributor will only drop down into the slot in one position. If he is 180° off he will have to loosen the rotor and turn just the rotor 180° to line up with TDC on #1 compression stroke. No need to lift the distributor.

[QUOTE=JayJay;2293572]I believe OP stated he was using the NuRex tool.

JayJay, Please read what I was referring too. Regardless if you use the Nurex tool or not, you can not just lift the distributor and turn it 180°!

[JayJay]

[QUOTE=Y-Blockhead;2293610]

Originally Posted by JayJay

I believe OP stated he was using the NuRex tool.

JayJay, Please read what I was referring too. Regardless if you use the Nurex tool or not, you can not just lift the distributor and turn it 180°!

YB - I agree, and wasn’t trying to imply otherwise. If the distributor is properly in the head and the rotor is pointing 180 degrees out, then likely you have the exhaust stroke, not the compression stroke.

[fried okra]

Thanks....I've cranked the engine trying to start it since dropping the distributor in.

Does that make a difference possibly?

[ModelA29]

Originally Posted by fried okra

Thanks....I've cranked the engine trying to start it since dropping the distributor in.

Does that make a difference possibly?

You can lift it anywhere and turn it 180 degrees so it drops back into the drive slot. When the pin is in the dimple it's always at TDC.

[J Franklin]

TDC on # 1 on the compression stroke? Double check if not verified.

[rotorwrench]

The model A distributor is rather unique in that the breaker cam can be positioned in any location. The cam gears don't always have a deep dimple to indicate position. Some are so shallow that they can be hard to detect. Roll it up on the #1 cylinder compression stroke and start feeling for it before it reaches TDC. Make certain it's on compression and not exhaust. Once it is positioned, the breaker cam can be positioned to fire #1. Be sure the spark control lever is properly positioned before setting the breaker opening point. The distributor rotor is set with the breaker cam so it should align with the #1 terminal.

[700rpm]

I always make that gear dimple a little deeper when I put in an new cam gear.

[fried okra]

rotorwrench....I saw the piston coming up flush with the top of the block, so I assume that is on compression stroke?

[abachman3]

The piston comes up twice in each cycle. Once is compression, the second is exhaust.

[JayJay]

Okra - when the piston is rising before TDC, on compression stroke both valves are shut tight. After you pass TDC both valves remain shut tight. This is the TDC you want to set the timing. I’ve found that the NuRex tool does a fine job when used as directed.

When on exhaust stroke, when the piston is rising before TDC the exhaust valve is open. After TDC the intake valve opens.

You can watch the valves through the spark plug hole.

Silly point, but you are rotating the engine clockwise (when viewed from the front)?

[fried okra]

Thanks JayJay....will need to check if can see the valves at TDC....just been looking at the piston.

Should the distributor rotor be at #1 plug contact in distributor on both exhaust and compression stroke when piston at TDC?

Yep, been been rotating engine clockwise when viewed from the front....thx.

[JayJay]

Originally Posted by fried okra

Thanks JayJay....will need to check if can see the valves at TDC....just been looking at the piston.

Should the distributor rotor be at #1 plug contact in distributor on both exhaust and compression stroke when piston at TDC?

Yep, been been rotating engine clockwise when viewed from the front....thx.

Distributor is driven by the camshaft. One revolution of the camshaft (and one revolution of the distributor) equals two revolutions of the crankshaft. So no, TDC of #1 cylinder on compression the distributor rotor points to #1, and at TDC of #1 cylinder on exhaust (which is TDC on compression of #4 cylinder) the rotor points to #4.

[ModelA29]

Originally Posted by fried okra

Should the distributor rotor be at #1 plug contact in distributor on both exhaust and compression stroke when piston at TDC?

No it only points at #1 when it fires on the compression stroke.
It turns 1/2 crank speed so it fires the plug every other up stroke of the piston.

[mcgarrett]

fried okra,
I have found this to be the most helpful information source when it concerns ignition timing, tune-ups, etc.

http://www.modelabasics.com/Ignition.htm

[mcgarrett]

http://www.modelabasics.com/Ignition.htm