Installing LED stoplights?

[31 Model A]

Does a part of the center divider have to be cut out to accommodate the wire to keep it from being cut into when putting the light back into the taillight section?

[Tom Wesenberg]

I installed some for a friend and didn't have to do any cutting.

[Ford1931]

Are there LED lights that look fairly stock when they are not on? I have seen some that really look out of place on a stock car.

[Patrick L.]

Originally Posted by Ford1931

Are there LED lights that look fairly stock when they are not on? I have seen some that really look out of place on a stock car.

The only ones that I've seen look stock until they are lit.

[31 Model A]

These came from Snyders. The red wire that connect top board with bottom board cuts in the middle of the seperation.

[Patrick L.]

Sponsored Links (Register now to hide all advertisements)

Originally Posted by 31 Model A

These came from Snyders. The red wire that connect top board with bottom board cuts in the middle of the seperation.

Not sure what you meant by the last sentence, but, I cut the jumper wire [red]. There were no instructions stating that, but, apparently these lights are for other installations also.

[Tom Wesenberg]

Yes, the ones I installed for a friend also needed to have the red wire cut.

[CarlG]

I just installed these in my regular Model A teacup tail lights. They look pretty much like the original glass lenses. If you prefer, they come in red/amber also. Most of our guys (me included) opted for the all red, just to be consistent with what people expect.

[Y-Blockhead]

I seem to remember if you install with the red wire not cut, all the LED's are on when the lights are turned on and become brighter when the brakes are applied.

When the red wire is cut, the upper and lower LED's are separated like the stock light, bottom side on with headlights, top side on with brakes.

If using option 1, uncut wire, you need to modify the separator for the wire to pass thru.

[31 Model A]

Originally Posted by Y-Blockhead

I seem to remember if you install with the red wire not cut, all the LED's are on when the lights are turned on and become brighter when the brakes are applied.

When the red wire is cut, the upper and lower LED's are separated like the stock light, bottom side on with headlights, top side on with brakes.

If using option 1, uncut wire, you need to modify the separator for the wire to pass thru.

I went with all red, to be noticed better. I doubt if I'll ever do any night time driving but quite a bit of daylight. Now, if the whole light is brighter when brake is applied, would that not be more noticeable?

[tbirdtbird]

you don't even need the separator with the LEDs pictured. Notching it would cause no harm

[31 Model A]

Got them in, did not cut any wire, brake light left works great, break light right does not work. Thought maybe I had cut the jumper red wire, took it back off, no cut, put the old bulbs back in, brake light still doesn't work. Put LED back on, running light left side works, gets brighter when brake is applied. Right side...nothing, no running nor stop.

[Patrick L.]

Originally Posted by 31 Model A

Got them in, did not cut any wire, brake light left works great, break light right does not work. Thought maybe I had cut the jumper red wire, took it back off, no cut, put the old bulbs back in, brake light still doesn't work. Put LED back on, running light left side works, gets brighter when brake is applied. Right side...nothing, no running nor stop.

Sounds like its time to get out the volt meter or test light. Once you the right side is working, I think you'll probably want to cut the red jumper.

If you decide to hook up signals, that'll be fun. But, we'll get them working too.

[31 Model A]

Originally Posted by Patrick L.

Sounds like its time to get out the volt meter or test light. Once you the right side is working, I think you'll probably want to cut the red jumper.

If you decide to hook up signals, that'll be fun. But, we'll get them working too.

Volt Meter????? What's a Volt Meter????? Just a bit of jocularity!!!! I'll put one on my shopping list for my next trip out. Sarah best not start talking diamond studded headlights!!!!!!

Turn signals???? Started on them today too.

Time for a cup of joe..................

[31 Model A]

Originally Posted by Patrick L.

If you decide to hook up signals, that'll be fun. But, we'll get them working too.

I decided to go with Logo-Lites. I see many A owners have them and they look OK. I got the lights bolted to the bumpers today, no wiring yet. Maybe tomorrow.

I'll do some reading tonight in my A books about tail lights.

-10 to -20 here tomorrow wind chill..................Brrrrr!!!

[31 Model A]

The running light right side was working about ten days ago when I last ran Sarah, break light, can't say.

[Y-Blockhead]

Check your grounds...

[31 Model A]

Originally Posted by Y-Blockhead

Check your grounds...

Will do first thing tomorrow when the garage has heat again.

[Y-Blockhead]

I would certainly think so. That is the way mine is set up. I also have my center light, looks clear but has 12 5mm RED LED's in it.

[Gus]

I like your light. Do you happen to know the specs of the LEDs you used? Lumens? MCD? I want to make something similar as a lightbar in the back window. Do you have a 6 volt pos ground? Thanks