The Ford Barn

Lawson Cox · 02-26-2022, 10:07 AM

My source for original nuts and bolts for 60HP sold out, apparently to someone here on the barn. Anyhow, I need a complete set of original bolts and washers for the intake manifold on a 60HP. I know they are being reproduced but I want to stay 100% original if possible. I would venture to say 60 and 85 manifold bolts are the same. Can anyone help me out. My direct email is [email protected]. Thanks. This is on the Early V8 forum as well.

Lawson

Kube · 02-26-2022, 11:24 AM

I know you are looking for the air cleaner wing nut as well.
Here ya go: eBay 393958248233

Lawson Cox · 02-26-2022, 02:34 PM

Thanks Kube. The one I lost was off of an air cleaner I sold on eBay. I just went down to the hardware store and got one and replaced it. I told the buyer about it before I shipped it. He was very understanding. I still have not found it. Today I was bead blasting the intake for the display engine and dropped the big washer off of the generator mount. Can't find that either. I am going to get rid of that damned old rug. I can't hear a thing I drop. The sound gives you a little bit of a clue as to where it went. LOL

flatjack9 · 02-26-2022, 02:38 PM

Need to poke around with a good magnet.

Lawson Cox · 02-26-2022, 02:57 PM

Quote:

Originally Posted by flatjack9

Need to poke around with a good magnet.

I don't have that big of a magnet/ LOL

cas3 · 02-26-2022, 03:13 PM

Sponsored Links (Register now to hide all advertisements)

It is amazing the skill we learn when something drops, freeze ! listen! what did it hit? how far did it roll? did it bounce? My messy shop makes it more challenging to find

51504bat · 02-26-2022, 04:14 PM

Quote:

Originally Posted by Lawson Cox

I don't have that big of a magnet/ LOL

Magnet from an old car speaker works great.

Lawson Cox · 02-26-2022, 04:42 PM

Well, I found the washer off of the manifold. Now, where's the wing nut, and my generator cutout with the B. Just damn. LOL

02-26-2022, 10:07 AM	#1
Lawson Cox Senior Member Join Date: May 2010 Location: Above the gnat line in Georgia Posts: 7,082	Need Original intake manifold bolts and washers for 60HP My source for original nuts and bolts for 60HP sold out, apparently to someone here on the barn. Anyhow, I need a complete set of original bolts and washers for the intake manifold on a 60HP. I know they are being reproduced but I want to stay 100% original if possible. I would venture to say 60 and 85 manifold bolts are the same. Can anyone help me out. My direct email is [email protected]. Thanks. This is on the Early V8 forum as well. Lawson __________________ Life is like a roll of toilet paper. The closer to the end, the faster it goes. It is better to be seen, than viewed. "We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm". Last edited by Lawson Cox; 02-26-2022 at 10:15 AM.

02-26-2022, 11:24 AM	#2
Kube Senior Member Join Date: May 2010 Location: Wisconsin, USA Posts: 9,852	Re: Need Original intake manifold bolts and washers for 60HP I know you are looking for the air cleaner wing nut as well. Here ya go: eBay 393958248233 __________________ "I can explain it for you. However, I can't understand it for you".

02-26-2022, 02:34 PM	#3
Lawson Cox Senior Member Join Date: May 2010 Location: Above the gnat line in Georgia Posts: 7,082	Re: Need Original intake manifold bolts and washers for 60HP Thanks Kube. The one I lost was off of an air cleaner I sold on eBay. I just went down to the hardware store and got one and replaced it. I told the buyer about it before I shipped it. He was very understanding. I still have not found it. Today I was bead blasting the intake for the display engine and dropped the big washer off of the generator mount. Can't find that either. I am going to get rid of that damned old rug. I can't hear a thing I drop. The sound gives you a little bit of a clue as to where it went. LOL __________________ Life is like a roll of toilet paper. The closer to the end, the faster it goes. It is better to be seen, than viewed. "We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm".

02-26-2022, 02:38 PM	#4
flatjack9 Senior Member Join Date: May 2010 Location: Oshkosh, Wi Posts: 4,600	Re: Need Original intake manifold bolts and washers for 60HP Need to poke around with a good magnet.

02-26-2022, 03:13 PM	#6
cas3 Senior Member Join Date: Jan 2011 Location: Beverly Kansas Posts: 5,301	Re: Need Original intake manifold bolts and washers for 60HP Sponsored Links (Register now to hide all advertisements) It is amazing the skill we learn when something drops, freeze ! listen! what did it hit? how far did it roll? did it bounce? My messy shop makes it more challenging to find

02-26-2022, 04:42 PM	#8
Lawson Cox Senior Member Join Date: May 2010 Location: Above the gnat line in Georgia Posts: 7,082	Re: Need Original intake manifold bolts and washers for 60HP Well, I found the washer off of the manifold. Now, where's the wing nut, and my generator cutout with the B. Just damn. LOL __________________ Life is like a roll of toilet paper. The closer to the end, the faster it goes. It is better to be seen, than viewed. "We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm".