The Ford Barn

Rowdy · 01-11-2016, 11:01 AM

As the original thread seems to be a muttled mess, so I thought I would start a new one with where I am in the hunt for patterns etc.

I bought all of the prints from the Benson for the rear door and the rear floor subrail. Borrowed patterns for the piece above the door, hinge pillar, latch pillar and both side subrail pieces from Don Graves. Will be borrowing the quarter panel piece located at beltline from him also. Roger Gash sent me the add panel backer pieces. I already had the vertical pieces at the rear of the quarter panels.

I am still looking for the rain gutter backing pieces,rear trim strip piece ( might be the same as tudor) all of the rear corner pieces and correct dimensions (width and thickness) for the floor wood. Thanks Rod

Rowdy · 01-12-2016, 12:55 PM

Is anyone going to the Benson this winter that might help to confirm thickness, width, joint design and screw hole spacing of the floor planking? Thanks Rod

Rowdy · 01-12-2016, 04:40 PM

Sponsored Links (Register now to hide all advertisements)

I do not seem to be able to find my notes. Does anyone have an exact measurement of how much would need to be added to the tudor wood rain gutter backers for the correct length for the delivery? Might be easier to find a pattern from a tudor and add on the needed length when making them.

If someone has an intact piece of rain gutter wood from a 28-29 tudor I could borrow and take to Don Graves shop in Febuary I could easily make these pieces after comparing the length of the one on the delivery in his shop.Thanks.Rod

01-11-2016, 11:01 AM	#1
Rowdy BANNED Join Date: May 2010 Location: Gothenburg Nebraska Just off I-80 Posts: 4,893	Update on Looking For Wood Patterns 29 130-A Delivery As the original thread seems to be a muttled mess, so I thought I would start a new one with where I am in the hunt for patterns etc. I bought all of the prints from the Benson for the rear door and the rear floor subrail. Borrowed patterns for the piece above the door, hinge pillar, latch pillar and both side subrail pieces from Don Graves. Will be borrowing the quarter panel piece located at beltline from him also. Roger Gash sent me the add panel backer pieces. I already had the vertical pieces at the rear of the quarter panels. I am still looking for the rain gutter backing pieces,rear trim strip piece ( might be the same as tudor) all of the rear corner pieces and correct dimensions (width and thickness) for the floor wood. Thanks Rod __________________ Do the RIGHT thing - Support the H.A.M.B. Alliance!!!! Last edited by Rowdy; 01-18-2016 at 02:51 PM.

01-12-2016, 12:55 PM	#2
Rowdy BANNED Join Date: May 2010 Location: Gothenburg Nebraska Just off I-80 Posts: 4,893	Re: Update on Looking For Wood Patterns 29 130-A Delivery Is anyone going to the Benson this winter that might help to confirm thickness, width, joint design and screw hole spacing of the floor planking? Thanks Rod __________________ Do the RIGHT thing - Support the H.A.M.B. Alliance!!!!

01-12-2016, 04:40 PM	#3
Rowdy BANNED Join Date: May 2010 Location: Gothenburg Nebraska Just off I-80 Posts: 4,893	Re: Update on Looking For Wood Patterns 29 130-A Delivery Sponsored Links (Register now to hide all advertisements) I do not seem to be able to find my notes. Does anyone have an exact measurement of how much would need to be added to the tudor wood rain gutter backers for the correct length for the delivery? Might be easier to find a pattern from a tudor and add on the needed length when making them. If someone has an intact piece of rain gutter wood from a 28-29 tudor I could borrow and take to Don Graves shop in Febuary I could easily make these pieces after comparing the length of the one on the delivery in his shop.Thanks.Rod __________________ Do the RIGHT thing - Support the H.A.M.B. Alliance!!!! Last edited by Rowdy; 01-12-2016 at 07:47 PM.