The Ford Barn

russcc · 08-06-2015, 02:55 PM

This looks like some type of Ford trans. The bell housing is early Ford. The serial # as I read it on the bell housing is HI 50823. That's all I see or can read. It has long OD tail shaft for a torque tube rear end. What is it ?
Please see photos. Thank you.

40cpe · 08-06-2015, 03:45 PM

probably lincoln

NealinCA · 08-06-2015, 04:40 PM

Yes, 46-48 Lincoln.

rotorwrench · 08-06-2015, 05:55 PM

Although they are way long, they are the only ones FoMoCo used that had a closed torque tube drive.

Russ/40 · 08-06-2015, 06:45 PM

Uses the Borg Warner overdrive components.

Mac VP · 08-06-2015, 07:11 PM

Sponsored Links (Register now to hide all advertisements)

I am rebuilding one of these at our shop right now. Uses the LZ gearset (25 or 26 tooth cluster gear). The planetary, sun gear, and freewheel cam are all the normal R 10 parts. The OD housing is pretty unique with an extra bearing supporting the OD mainshaft. It's a pretty heavy brute too.

russcc · 08-07-2015, 06:14 AM

Thank you all for your help. I was think it was an LZ, but was not sure. Nice to know Mac can rebuild them, and that they use BW OD parts.

38 coupe · 08-08-2015, 04:08 PM

Don't lose the solenoid, even if it doesn't work. That solenoid is Zephyr overdrive specific with a very long shaft.

08-06-2015, 03:45 PM	#2
40cpe Senior Member Join Date: May 2010 Location: Star, MS Posts: 4,120	Re: OD trans ID help needed. probably lincoln

08-06-2015, 04:40 PM	#3
NealinCA Senior Member Join Date: May 2010 Location: Central Coast, Calif. Posts: 868	Re: OD trans ID help needed. Yes, 46-48 Lincoln.

08-06-2015, 05:55 PM	#4
rotorwrench Senior Member Join Date: Jun 2010 Location: San Antonio, Texas Posts: 17,410	Re: OD trans ID help needed. Although they are way long, they are the only ones FoMoCo used that had a closed torque tube drive.

08-06-2015, 06:45 PM	#5
Russ/40 Senior Member Join Date: May 2010 Location: Santee, California Posts: 3,505	Re: OD trans ID help needed. Uses the Borg Warner overdrive components.

08-06-2015, 07:11 PM	#6
Mac VP Senior Member Join Date: May 2010 Location: Cincinnati, OH Posts: 1,430	Re: OD trans ID help needed. Sponsored Links (Register now to hide all advertisements) I am rebuilding one of these at our shop right now. Uses the LZ gearset (25 or 26 tooth cluster gear). The planetary, sun gear, and freewheel cam are all the normal R 10 parts. The OD housing is pretty unique with an extra bearing supporting the OD mainshaft. It's a pretty heavy brute too. __________________ VANPELT SALES LLC Cincinnati, Ohio Office: 513-724-9486 www.vanpeltsales.com www.classictransmission.com

08-07-2015, 06:14 AM	#7
russcc Senior Member Join Date: May 2010 Posts: 2,871	Re: OD trans ID help needed. Thank you all for your help. I was think it was an LZ, but was not sure. Nice to know Mac can rebuild them, and that they use BW OD parts.

08-08-2015, 04:08 PM	#8
38 coupe Senior Member Join Date: May 2010 Location: South Texas Posts: 2,042	Re: OD trans ID help needed. Don't lose the solenoid, even if it doesn't work. That solenoid is Zephyr overdrive specific with a very long shaft.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode