![]() |
#1 |
Member
Join Date: Nov 2011
Location: Wilmington New York
Posts: 94
|
![]()
I believe that this is a 1950 or 1951 mercury pan ? On the rear of the pan are 3 fine thread bolts sticking out. These bolts are 3/8 thread. What was the purpose of these bolts? It appears to be factory installed as the head of the bolts are visible through the pan.If not needed can it be removed to clean up the bottom of the pan.Thanks in advance. Bill
|
![]() |
![]() |
![]() |
#2 |
Senior Member
Join Date: May 2010
Location: Gardiner Me.
Posts: 4,200
|
![]()
Some of the starter plates have shelfe built on that goes over those bolts. You want to make sure you use the correct starter plate that goes with the bell housing that bolts to your engine. Walt
|
![]() |
![]() |
Sponsored Links (Register now to hide all advertisements) |
|
![]() |
#3 |
Member
Join Date: Nov 2011
Location: Wilmington New York
Posts: 94
|
![]()
Thanks Walt.Do you or someone else know if all the Mercs have the "Shelf" welded on the starter plate?My problem is that I obtained 2 engines 1 ford 1 merc.But the previous owner decided to take them completely apart and put all the pieces in the same box without marking or seperating them.
![]() |
![]() |
![]() |
![]() |
#4 |
Senior Member
Join Date: May 2010
Location: Lee's Summit, Mo
Posts: 347
|
![]()
Does your pan have a baffle in it. It looks like a Mercury oil pan to me.
|
![]() |
![]() |
![]() |
#5 |
Senior Member
Join Date: May 2010
Location: Regina Canada
Posts: 1,337
|
![]()
Here is a link to a PDF file. Slow loading but well worth the look.
http://www.flatheadv8.org/bellhousing.pdf |
![]() |
![]() |
![]() |
#6 |
Senior Member
Join Date: May 2010
Location: Lee's Summit, Mo
Posts: 347
|
![]() Sponsored Links (Register now to hide all advertisements)
|
![]() |
![]() |
![]() |
#7 | ||
Member
Join Date: Nov 2011
Location: Wilmington New York
Posts: 94
|
![]() Quote:
Quote:
4tford I have attempted to open the link,something with my computer won,t allow it to open??I even went to there site and registered but that didn't help? 26 lakes yes there is a baffle in the pan Is there a problem with running the merc pan on a ford block?Are the oil pumps the same and just the pickup screens are different? Thanks for the patience I'm trying to get my block off to the machine shop and i want to make sure everything is in order Bill |
||
![]() |
![]() |
![]() |
#8 |
Member
Join Date: Nov 2011
Location: Wilmington New York
Posts: 94
|
![]()
4tford I got the link to open on my laptop That will keep me busy for a while.Now I understand what you were talking about Walt Thanks again
|
![]() |
![]() |
![]() |
#9 |
Senior Member
Join Date: May 2010
Location: Lee's Summit, Mo
Posts: 347
|
![]()
You can run the Mercury pan on the Ford block. All blocks are the "same". Oil pans have the same mounting surface. It's the crank in the Mercury that is different.
|
![]() |
![]() |
![]() |
#10 |
Senior Member
Join Date: May 2010
Location: Kerrville, Tx
Posts: 2,880
|
![]()
I have a Merc oil pump with the baffle if interested.
|
![]() |
![]() |
![]() |
|
|
Sponsored Links (Register now to hide all advertisements) |
|