07-09-2024, 10:29 AM
|
#1 |
|
Senior Member
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,428
|
Needed
I'm in dire need of a 46-48 generator armature (my re-builder can't get one),
other years might work(?). Thanks in advance. Paul in CT |
|
|
|
07-09-2024, 10:45 AM
|
#2 |
|
Senior Member
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 4,807
|
Re: Needed
Try Steve Blancard here on the Barn he goes by ndnchf OR where it me I would send HIM your generator and let him rebuild it for you....NONE better than him and his work!!!! He is "TOP NOTCH". It will be better than when it was new and 100% concours. You can youtube his videos he had done on a few generators and his quality of work and upgraded bearings as well as he has posted both pictures and links to his work here on the barn!!!
https://www.fordbarn.com/forum/showthread.php?t=339681 https://www.fordbarn.com/forum/showthread.php?t=339680 Last edited by rockfla; 07-09-2024 at 10:54 AM. |
|
|
|
| Sponsored Links (Register now to hide all advertisements) |
|
|
|
07-09-2024, 04:30 PM
|
#3 |
|
Senior Member
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,428
|
Re: Needed
to the top
|
|
|
|
|
07-10-2024, 07:06 AM
|
#4 |
|
Senior Member
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 4,807
|
Re: Needed
Check with Fred at Southside Obsolete
|
|
|
|
|
07-10-2024, 07:23 AM
|
#5 |
|
Senior Member
Join Date: May 2010
Location: Southern France
Posts: 5,837
|
Re: Needed
Will this work?
https://www.ebay.com/itm/387039447950 |
|
|
|
07-10-2024, 10:05 AM
|
#6 |
|
Senior Member
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,428
|
Re: Needed
Sponsored Links (Register now to hide all advertisements)
Paul in CT |
|
|
|
|
07-10-2024, 10:39 AM
|
#7 |
|
Senior Member
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,428
|
Re: Needed
Just ordered it ! ! Thanks again.
|
|
|
|
|
07-11-2024, 05:37 AM
|
#8 |
|
Senior Member
Join Date: May 2012
Location: Fredericksburg, Virginia
Posts: 1,088
|
Re: Needed
Glad you found one. If I can be of any assistance, let me know.
Rockfla - thanks for the kind words and recommendation. Steve Blancard |
|
|
|
|
07-11-2024, 07:00 AM
|
#9 |
|
Senior Member
Join Date: May 2010
Location: on the Littlefield
Posts: 6,556
|
Re: Needed
I would expect the original 46-48 armature to have a groove at the end of the threads for the clip that prevents the threaded pulley from unscrewing.
the ones without the groove were for pulleys held on with a nut |
|
|
|
 |
«
Previous Thread
|
Next Thread
»
Linear Mode
|
|
| Sponsored Links (Register now to hide all advertisements) |
|
|
All times are GMT -5. The time now is 11:39 PM.