Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 04-10-2025, 07:32 PM   #1
TomC750
Senior Member
 
TomC750's Avatar
 
Join Date: Dec 2024
Location: Eastern Tennessee
Posts: 272
Default Compression

Searched the forum and other places for acceptable compression numbers for my '41 Merc. Mine range between 70# and 80#. Any help?
__________________
TomC750

1949 8NV8 Ford tractor
1930 1 Ton White
1941 Mercury Sedan Coupe
TomC750 is offline   Reply With Quote
Old 04-10-2025, 08:02 PM   #2
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 11,639
Default Re: Compression

It'll probably start and run OK with those numbers. Before I changed the engine in my '51, it was between 85 and 100 on all eight and it was OK to drive daily. You may be OK (for a while) if they're all about the same. Hopefully, a couple dosed of Marvel Mystery Oil and some driving will cause the situation to improve. Maybe a couple of shots of Sea Foam down the carb, as well.

Don't expect any "seat of the pants" thrills, though.
tubman is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 04-10-2025, 08:43 PM   #3
TomC750
Senior Member
 
TomC750's Avatar
 
Join Date: Dec 2024
Location: Eastern Tennessee
Posts: 272
Default Re: Compression

Quote:
Originally Posted by tubman View Post
It'll probably start and run OK with those numbers. Before I changed the engine in my '51, it was between 85 and 100 on all eight and it was OK to drive daily. You may be OK (for a while) if they're all about the same. Hopefully, a couple dosed of Marvel Mystery Oil and some driving will cause the situation to improve. Maybe a couple of shots of Sea Foam down the carb, as well.

Don't expect any "seat of the pants" thrills, though.
Tubman, thanks for the response. This vehicle does not smoke or burn oil. It wants to run strong intermittently, but has a tuneup problem I have not figured out. I do suspect a valve sticking occasionally when listening to the exhaust at idle. But there is something else. I am going to put an ignition analyzer on it tomorrow.
__________________
TomC750

1949 8NV8 Ford tractor
1930 1 Ton White
1941 Mercury Sedan Coupe
TomC750 is offline   Reply With Quote
Old 04-10-2025, 08:47 PM   #4
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 11,639
Default Re: Compression

Check for a weak condenser. Prepare to have to try one or more FLAPS condensers before you get a good one. I hear Vertex magneto condensers are very good, but they have to be special ordered.
tubman is offline   Reply With Quote
Old 04-11-2025, 07:51 AM   #5
34fordy
Senior Member
 
34fordy's Avatar
 
Join Date: Dec 2014
Location: Fort dodge, Iowa
Posts: 1,229
Default Re: Compression

Quote:
Originally Posted by tubman View Post
Check for a weak condenser. Prepare to have to try one or more FLAPS condensers before you get a good one. I hear Vertex magneto condensers are very good, but they have to be special ordered.
I have no idea what a "flaps" condenser is and the Mallory is good but I would try a "TUBMAN TRASHCAN" for peace of mind!
34fordy is offline   Reply With Quote
Old 04-11-2025, 07:56 AM   #6
corvette8n
Senior Member
 
corvette8n's Avatar
 
Join Date: Jul 2010
Location: 36 miles north of Albany NY
Posts: 3,198
Default Re: Compression

Sponsored Links (Register now to hide all advertisements)
My ‘41 is 60lbs on all 8 and it burns a quart every 40 miles, but I still drive it to car shows several times in the summer. Post some pictures of your Merc, I almost bought a two-tone 1941 Mercury w/jump seats but the paperwork was wonky so I passed.
corvette8n is offline   Reply With Quote
Old 04-11-2025, 09:05 AM   #7
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 11,639
Default Re: Compression

Sorry, "H.A.M.B. term". "FLAPS" - Friendly local auto part store.

For the record, I am now out of condensers. Any future supply depends on whether I can talk my partner into making some more when I get back to Minnesota.
tubman is offline   Reply With Quote
Old 04-11-2025, 10:07 AM   #8
mfirth
Senior Member
 
Join Date: Aug 2017
Location: ohio
Posts: 1,103
Default Re: Compression

Stores like N A P A. Standing joke here is : Never Any Parts Available. The guys who work there are actually GR8 & get what they don't have next day.
mfirth is offline   Reply With Quote
Old 04-11-2025, 10:26 AM   #9
Drbrown
Senior Member
 
Drbrown's Avatar
 
Join Date: Oct 2013
Location: Glens Falls NY
Posts: 1,355
Default Re: Compression

Regarding concern about valves, attach a vacuum meter at you carb. If the indicator needle stumbles, jumps etc it could indicate a sticky or badly seated valve. This is not unusual for engines that don't get enough use. If so, next step might be to add some MMO .... a bit down the carb and a quart in the oil. At purchase my '47 had same symptom and the MMO cleared it up.
Drbrown is offline   Reply With Quote
Old 04-11-2025, 12:24 PM   #10
TomC750
Senior Member
 
TomC750's Avatar
 
Join Date: Dec 2024
Location: Eastern Tennessee
Posts: 272
Default Re: Compression

Quote:
Originally Posted by Drbrown View Post
Regarding concern about valves, attach a vacuum meter at you carb. If the indicator needle stumbles, jumps etc it could indicate a sticky or badly seated valve. This is not unusual for engines that don't get enough use. If so, next step might be to add some MMO .... a bit down the carb and a quart in the oil. At purchase my '47 had same symptom and the MMO cleared it up.
I had a vacuum gauge on my engine, it fluttered a little bit, I did run some Seafoam through it, no change. It is not one valve that is a problem, it stumbles on all cylinders intermittently. I am going to do the MMO however.
__________________
TomC750

1949 8NV8 Ford tractor
1930 1 Ton White
1941 Mercury Sedan Coupe
TomC750 is offline   Reply With Quote
Old 04-11-2025, 12:27 PM   #11
TomC750
Senior Member
 
TomC750's Avatar
 
Join Date: Dec 2024
Location: Eastern Tennessee
Posts: 272
Default Re: Compression

Quote:
Originally Posted by tubman View Post
Check for a weak condenser. Prepare to have to try one or more FLAPS condensers before you get a good one. I hear Vertex magneto condensers are very good, but they have to be special ordered.
Charlie installed a new condenser, (NAPA) possible it is bad I suppose. I had my old ignition analyzer on it this morning, rather inconclusive. blurry trace, jumped around quite a bit.
__________________
TomC750

1949 8NV8 Ford tractor
1930 1 Ton White
1941 Mercury Sedan Coupe

Last edited by TomC750; 04-11-2025 at 12:33 PM.
TomC750 is offline   Reply With Quote
Old 04-11-2025, 12:30 PM   #12
TomC750
Senior Member
 
TomC750's Avatar
 
Join Date: Dec 2024
Location: Eastern Tennessee
Posts: 272
Default Re: Compression

Quote:
Originally Posted by tubman View Post
It'll probably start and run OK with those numbers. Before I changed the engine in my '51, it was between 85 and 100 on all eight and it was OK to drive daily. You may be OK (for a while) if they're all about the same. Hopefully, a couple dosed of Marvel Mystery Oil and some driving will cause the situation to improve. Maybe a couple of shots of Sea Foam down the carb, as well.

Don't expect any "seat of the pants" thrills, though.
When it pulls, it pulls strong, even when missing intermittently.
__________________
TomC750

1949 8NV8 Ford tractor
1930 1 Ton White
1941 Mercury Sedan Coupe
TomC750 is offline   Reply With Quote
Old 04-11-2025, 12:40 PM   #13
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 11,639
Default Re: Compression

That's encouraging.
tubman is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 12:10 PM.