The Ford Barn

Thirtyeight · 03-26-2015, 06:01 PM

I recently installed a new repro tool box and tail pan on my 38' Conv. and I would like to put the rear bumper back on. But, what I don't know is the location and dimensions of the two slots for the bumper brackets and I would like to get this right.

Any help would be greatly appreciated.

cmbrucew · 03-26-2015, 07:18 PM

38
This topic was discussed last month I believe.
Check the archives.
Bruce

johnny · 03-26-2015, 08:31 PM

I am temping to send you a picture of the measurements you need if the picture method does not work, I will list the measurements for you. I can't seem to get the picture to work .So here are the measurements these are the finish sizes ,the cut out should be about 3/8 less for each side to allow for a flange to bend in So from the outer edge of the panel,1 3/8 to 1 7/16 in, 5 inches up from the bottom edge to the top of the opening which has some round to it . the finish opening is 1 3/8 wide . the measurement down from the lower bead to the top of the opening should be 3 1/2 inches.I will keep working on the picture also . Is your car the club or rumble seat model .If it is a club model I need information of the rear quarter filler panel, it fits behind the armrest and from the door striker post back to the seat. John. [email protected]

cmbrucew · 03-27-2015, 10:38 AM

https://www.fordbarn.com/forum/showth...er+irons+holes

38
Here is a thread that should help.
Bruce

swoopNZ · 03-27-2015, 06:39 PM

Sponsored Links (Register now to hide all advertisements)

3 feet ( 36 inches ) from center to center, between the top of the slots on my 38 and 39.

03-26-2015, 06:01 PM	#1
Thirtyeight Senior Member Join Date: Jun 2012 Posts: 181	38' Rear Tail Pan Dimension Question??? I recently installed a new repro tool box and tail pan on my 38' Conv. and I would like to put the rear bumper back on. But, what I don't know is the location and dimensions of the two slots for the bumper brackets and I would like to get this right. Any help would be greatly appreciated.

03-26-2015, 07:18 PM	#2
cmbrucew Senior Member Join Date: Dec 2010 Location: North of sandy ago, CA. Posts: 2,080	Re: 38' Rear Tail Pan Dimension Question??? 38 This topic was discussed last month I believe. Check the archives. Bruce __________________ Works good Lasts long time

03-26-2015, 08:31 PM	#3
johnny Senior Member Join Date: May 2010 Location: London On, Can. Posts: 377	Re: 38' Rear Tail Pan Dimension Question??? I am temping to send you a picture of the measurements you need if the picture method does not work, I will list the measurements for you. I can't seem to get the picture to work .So here are the measurements these are the finish sizes ,the cut out should be about 3/8 less for each side to allow for a flange to bend in So from the outer edge of the panel,1 3/8 to 1 7/16 in, 5 inches up from the bottom edge to the top of the opening which has some round to it . the finish opening is 1 3/8 wide . the measurement down from the lower bead to the top of the opening should be 3 1/2 inches.I will keep working on the picture also . Is your car the club or rumble seat model .If it is a club model I need information of the rear quarter filler panel, it fits behind the armrest and from the door striker post back to the seat. John. [email protected]

03-27-2015, 10:38 AM	#4
cmbrucew Senior Member Join Date: Dec 2010 Location: North of sandy ago, CA. Posts: 2,080	Re: 38' Rear Tail Pan Dimension Question??? https://www.fordbarn.com/forum/showth...er+irons+holes 38 Here is a thread that should help. Bruce __________________ Works good Lasts long time

03-27-2015, 06:39 PM	#5
swoopNZ MEMBER EMERITUS Join Date: May 2010 Location: New Zealand Posts: 1,380	Re: 38' Rear Tail Pan Dimension Question??? Sponsored Links (Register now to hide all advertisements) 3 feet ( 36 inches ) from center to center, between the top of the slots on my 38 and 39.