Forum: Early V8 (1932-53)
Today, 09:06 AM
|
Replies: 190
Views: 12,293
Re: 276 stroker from 35 years of parts
Hi GB. The cam gear bolts should be fine thread. Just make sure they are the right ones. If too long they will stick out the back of the cam flange.
Mart.
|
Forum: Early V8 (1932-53)
05-03-2024, 10:45 AM
|
Replies: 29
Views: 3,194
|
Forum: Early V8 (1932-53)
05-01-2024, 12:05 PM
|
Replies: 17
Views: 1,067
|
Forum: Early V8 (1932-53)
04-30-2024, 01:52 PM
|
Replies: 25
Views: 872
|
Forum: Early V8 (1932-53)
04-29-2024, 06:02 PM
|
Replies: 89
Views: 5,120
|
Forum: Early V8 (1932-53)
04-28-2024, 05:50 AM
|
Replies: 25
Views: 872
|
Forum: Early V8 (1932-53)
04-26-2024, 11:36 AM
|
Replies: 29
Views: 3,194
|
Forum: Early V8 (1932-53)
04-25-2024, 04:29 PM
|
Replies: 17
Views: 1,067
|
Forum: Early V8 (1932-53)
04-25-2024, 04:20 PM
|
Replies: 13
Views: 697
|
Forum: Early V8 (1932-53)
04-25-2024, 07:33 AM
|
Replies: 51
Views: 4,062
|
Forum: Early V8 (1932-53)
04-25-2024, 07:29 AM
|
Replies: 17
Views: 1,067
|
Forum: Early V8 (1932-53)
04-24-2024, 05:13 AM
|
Replies: 17
Views: 1,248
|
Forum: Early V8 (1932-53)
04-23-2024, 12:48 PM
|
Replies: 17
Views: 1,248
Re: Brake drum question
On earlier hubs and drums the drum fits over the hub. On later assemblies the drum fits on the inside of the hub. The drums are different. I think the early ones have the smaller ones and the later...
|
Forum: Early V8 (1932-53)
04-23-2024, 12:42 PM
|
Replies: 89
Views: 5,120
|
Forum: Early V8 (1932-53)
04-21-2024, 03:33 PM
|
Replies: 89
Views: 5,120
|
Forum: Early V8 (1932-53)
04-20-2024, 05:06 AM
|
Replies: 190
Views: 12,293
|
Forum: Early V8 (1932-53)
04-19-2024, 11:17 AM
|
Replies: 29
Views: 3,194
|
Forum: Early V8 (1932-53)
04-18-2024, 01:09 PM
|
Replies: 20
Views: 1,473
Re: Flat head back firing pop. pop over and over
As the vehicle is new to you and unknown it is very difficult to say what the problem might be. A full description of the truck and further info on when the problem occurs would also help. is it bad...
|
Forum: Early V8 (1932-53)
04-17-2024, 10:42 AM
|
Replies: 7
Views: 995
Re: Seen on Facebook
That's a pretty accurate representation of 90% of the videos I watch on youtube.
|
Forum: Early V8 (1932-53)
04-16-2024, 04:45 AM
|
Replies: 50
Views: 2,025
|
Forum: Early V8 (1932-53)
04-15-2024, 02:37 AM
|
Replies: 6
Views: 539
Re: Frame vin
Sometimes useful to hold a light at a very low angle to cast a shadow across the digits. Also use the camera in your phone to video the area from all angles and use macro mode. Then watch it on a...
|
Forum: Early V8 (1932-53)
04-13-2024, 01:31 PM
|
Replies: 89
Views: 5,120
|
Forum: Early V8 (1932-53)
04-12-2024, 10:37 AM
|
Replies: 29
Views: 3,194
|
Forum: Early V8 (1932-53)
04-11-2024, 07:14 AM
|
Replies: 7
Views: 608
Re: 6V vs 12V condenser
Sometimes the rotor arm gets weak on the helmet distributors and allows the spark to short to the shaft the rotor sits on. A new rotor might help or pit some heat shrink on the shaft. This, like many...
|
Forum: Early V8 (1932-53)
04-08-2024, 03:09 AM
|
Replies: 96
Views: 6,560
Re: Break-in gone wrong!
Is there any chance the block could have been modified at some point in the past for 90% full flow external filter? If so the horizontal passageway in the oil gallery might have a grub screw in it.
...
|