Go Back   The Ford Barn > Search Forums
Reload this Page Search Results

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 11 of 11
Search took 0.00 seconds. Search: Posts Made By: Hank/Mi
Forum: Early V8 (1932-53) 06-16-2013, 02:27 PM
Replies: 9
Views: 3,779
Posted By Hank/Mi
Re: 195/80R16 tires

Mike,
we really enjoyed it..might go back sometime this summer when it's not so crowded...we drove the A, AKA Anita.
Forum: Early V8 (1932-53) 06-15-2013, 10:19 AM
Replies: 9
Views: 3,779
Posted By Hank/Mi
Re: 195/80R16 tires

http://img.photobucket.com/albums/v28/minnie_04/Tires003.jpg

http://img.photobucket.com/albums/v28/minnie_04/Tires002.jpg

They are on 35 Ford wheels. They ride and handle good. We drove it to...
Forum: Model A (1928-31) 04-11-2013, 07:08 PM
Replies: 2
Views: 1,280
Posted By Hank/Mi
Speedometer gear

I have a 1931 coupe with 16 inch wheels, tire size 195 by 80 R16s, approximately 28 inches tall. Rear end ratio is 378. I have a 19 tooth gear which I think will be a little slow. Do you think 20 or...
Forum: Early V8 (1932-53) 04-11-2013, 07:03 PM
Replies: 0
Views: 1,336
Posted By Hank/Mi
Speedometer gear

wrong forum
Forum: Model A (1928-31) 11-15-2010, 06:45 PM
Replies: 10
Views: 3,182
Posted By Hank/Mi
Re: Head gasket

I like FelPro also, but they don't make copper one for a B head. I prefer copper, but I may have to go with the silicone. Snyders said you have to use a B style gasket with their 6:1 head. I think...
Forum: Model A (1928-31) 11-15-2010, 06:39 PM
Replies: 10
Views: 3,182
Posted By Hank/Mi
Re: Head gasket

I've use two silicone gaskets and one blew after 4 miles and the other was ready to blow @ 300 miles. It was blowing water out the over flow.
Forum: Model A (1928-31) 11-14-2010, 07:47 PM
Replies: 10
Views: 3,182
Posted By Hank/Mi
Head gasket

I can't seem to find a copper head gasket for a B engine with a 6:1 Snyder head. They say you have to use a B head gasket and I'm not fond of the silicone gasket. What would you guys recommend...
Forum: Model A (1928-31) 11-08-2010, 06:54 PM
Replies: 2
Views: 1,530
Posted By Hank/Mi
B head gasket

Does anyone know the number for a Felpro head gasket for a B engine?

TIA
Hank/MI
Forum: Model A (1928-31) 11-03-2010, 06:13 PM
Replies: 13
Views: 2,877
Posted By Hank/Mi
Re: Lifters?

@Ron, that was the condition of the bore when I bought the engine. Didn't realize it until I started it. It's just a junk diamond B engine. I purchased a reamer from mcmaster carr tonight.
So we...
Forum: Model A (1928-31) 11-02-2010, 06:22 PM
Replies: 13
Views: 2,877
Posted By Hank/Mi
Cool Lifters?

What can a person do when the lifter holes in the block are worn oblong? You can only buy 5/1000 over and I have about 25 over. Do you bore it and sleeve it? Any suggestions?

TIA
Hank
Forum: Model A (1928-31) 07-29-2010, 07:19 PM
Replies: 2
Views: 1,549
Posted By Hank/Mi
putting new top on model A coupe

I just purchased another coupe, it came with an additional new top and
aluminum moldings, but no instructions on how to install the top. Just
wondering if there might be a manual somewhere on the...
Showing results 1 to 11 of 11

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 01:12 PM.