Forum: Early V8 (1932-53)
02-14-2024, 12:32 AM
|
Replies: 21
Views: 1,378
|
Forum: Early V8 (1932-53)
10-17-2023, 02:00 PM
|
Replies: 1
Views: 437
Re: F100 steering box in 34 pickup
I did this very swap on my '34 pick-up a LONG time ago. I had the original steering box and the f100 for fit and comparison. I remember that I milled off (I'm a machinist) part of the f100 box...
|
Forum: Early V8 (1932-53)
12-14-2022, 12:13 PM
|
Replies: 10
Views: 1,312
|
Forum: Early V8 (1932-53)
05-21-2022, 12:21 AM
|
Replies: 18
Views: 2,625
Re: Flathead Blocks
Hi-Country Regional Group #28 of the Early Ford V8 Club of America is very active in the Denver metro and Rocky Mtn. areas. There is a Facebook page.
|
Forum: Early V8 (1932-53)
12-21-2021, 01:32 PM
|
Replies: 11
Views: 1,531
|
Forum: Early V8 (1932-53)
12-21-2021, 01:15 PM
|
Replies: 11
Views: 1,531
Re: 1935-37 LED Headlights
Here's what I found, I already had halogen (no relay) dim at idle, ok at speed. While searching for relay kit on ebay, bumped into a LED conversion. Bought both. I don't remember the brand, but turns...
|
Forum: Early V8 (1932-53)
09-30-2021, 02:11 PM
|
Replies: 16
Views: 1,820
Re: Just asking
I also bought a spot welder from harbor freight (220v) and found that all the areas of contact need to be freshly sanded between pieces and electrodes. Clamp pressure adjustment and switch on time...
|
Forum: Early V8 (1932-53)
06-01-2021, 12:12 PM
|
Replies: 10
Views: 1,273
Re: Epay
jimTN, the listings on bid and buy now are separated (didn't used to be) even though all listings is checked. I usually only look a day ahead on bid group, then go to bottom of page and move 3,4,5,10...
|
Forum: Early V8 (1932-53)
01-28-2021, 12:52 PM
|
Replies: 69
Views: 9,309
|
Forum: Early V8 (1932-53)
10-28-2020, 11:14 AM
|
Replies: 28
Views: 5,186
|
Forum: Early V8 (1932-53)
09-30-2020, 10:55 PM
|
Replies: 24
Views: 5,386
|
Forum: Early V8 (1932-53)
06-29-2020, 12:40 PM
|
Replies: 6
Views: 1,314
|
Forum: Early V8 (1932-53)
05-17-2020, 11:13 AM
|
Replies: 7
Views: 1,239
|
Forum: Early V8 (1932-53)
03-02-2020, 12:06 AM
|
Replies: 9
Views: 1,481
Re: 34 pickup cab assembly question
I had the roof off of my cab last summer, same question. Friction tape was my first thought but didn't want the sticky. I ended up using fender welt, minus the bead.
|
Forum: Early V8 (1932-53)
07-04-2019, 11:22 PM
|
Replies: 29
Views: 5,655
Re: STOLEN RODSTER north of Denver
Local Denver TV station aired report about theft and recovery. Very few details about recovery except it was found in a garage, little damage. Duane is very happy.
|
Forum: Early V8 (1932-53)
03-21-2019, 11:29 PM
|
Replies: 9
Views: 1,854
Re: 8ba in 36 5 window
Marvin, you may have to turn/grind forged stop off, then run a thread die on for 1" or so. Spin first nut down to have adjustable stop. Trap bellhousing with second nut. Lock washers.
|
Forum: Early V8 (1932-53)
01-18-2019, 01:05 AM
|
Replies: 12
Views: 2,172
Re: 1934 picku cab wood and seat
GearheadBill, it appears the shortest uprights have been cut off. There should be a rectangle hole with a tab in floor. That tab has a hole in it to screw to the bottom of wood. rbullockv8 shows the...
|
Forum: Early V8 (1932-53)
11-22-2018, 12:11 AM
|
Replies: 33
Views: 7,576
Re: valve seat cutters
Electro magnetic base drill would fill the bill, rpm might be too slow/high. Magnetic base mounts to cylinder deck with block on engine stand.
|
Forum: Early V8 (1932-53)
11-20-2018, 02:02 PM
|
Replies: 3
Views: 1,385
Re: 1934 Ford Pickup Floorboard Question
Fever, I checked mine today just to make sure. Guess what, NO HOLE. Maybe the difference is big truck and pickup. BTW thanks for pic, never knew how trans cover was held in place.
|
Forum: Early V8 (1932-53)
08-29-2018, 11:10 PM
|
Replies: 9
Views: 1,468
Re: 1934 driveline install help
Duke, just did that 2 weeks ago. Must have been a problem for me before, as I found self locking nuts (AN) on bottom and castle nuts on top. Also found my special tapered 11/16 socket to fit close to...
|
Forum: Early V8 (1932-53)
05-14-2018, 01:38 PM
|
Replies: 15
Views: 2,815
|
Forum: Early V8 (1932-53)
05-14-2018, 12:56 PM
|
Replies: 15
Views: 2,815
|
Forum: Early V8 (1932-53)
05-14-2018, 12:09 PM
|
Replies: 15
Views: 2,815
Re: Loadamatic and four barrel 49-53 ?
So what happens if I throw in Mallory dual point (was chevy, set-up by Bubba) with mechanical and vacuum advance? Where do I get the right vacuum signal?
|
Forum: Early V8 (1932-53)
08-14-2014, 09:51 PM
|
Replies: 39
Views: 7,510
Re: End of Rod & Custom
My next 2-1/2 years is Motor Trend!! YUCK. Would prefer to extend Street Rodder. Didn't get a choice. Recycle the paper.
|
Forum: Early V8 (1932-53)
07-06-2014, 07:52 PM
|
Replies: 35
Views: 9,644
Re: Flathead build on TV
I tuned in Powernation this morning on SpikeTV and lo and behold was part 2. Scat rotating assembly 4-1/4 stroke, I think. H-beam connecting rods. All buttoned up and dyno run too.
|