Forum: Model A (1928-31)
04-16-2024, 09:08 AM
|
Replies: 25
Views: 1,903
Re: Nu Rex ignition switch
I just installed the Nu Rex ignition switch but luckily my A had been converted to electronic ignition before I got it, and a similar switch was used with two wires. I like the original look of the...
|
Forum: Model A (1928-31)
02-19-2024, 03:06 PM
|
Replies: 58
Views: 3,126
|
Forum: Model A (1928-31)
01-30-2024, 04:05 PM
|
Replies: 29
Views: 2,102
|
Forum: Model A (1928-31)
12-30-2023, 11:04 AM
|
Replies: 37
Views: 2,638
|
Forum: Model A (1928-31)
12-26-2023, 11:04 PM
|
Replies: 21
Views: 1,465
Re: will not idle
Have you done a compression check on all the cylinders. Something I am guilty of, I tried setting the idle with the engine running too fast. These puppies idle slow and you have to adjust the idle...
|
Forum: Model A (1928-31)
12-10-2023, 11:12 PM
|
Replies: 35
Views: 8,834
Re: Model B carburetor
I have a B carb on my A, square float and replaced the missing brass baffle. I purchased the level gauge from Renners and have it set exactly as the picture above. It took 2 tries because I found out...
|
Forum: Model A (1928-31)
10-08-2023, 02:07 PM
|
Replies: 6
Views: 653
Re: Light Bar Installation
I purchased the stainless bolts from a popular vendor and would not do it again because, number one they were almost too short, #2 they galled and were a pain when it was time to remove and 3 they...
|
Forum: Model A (1928-31)
09-19-2023, 04:12 PM
|
Replies: 16
Views: 1,518
Re: Sta-Bil 360
I have been using Sta-Bil 360 in my boat for several years. It is the marine version of Sta-Bil if I remember correctly it is good for fuel storage up to 12 months. My boat isn't used often these...
|
Forum: Model A (1928-31)
09-09-2023, 12:47 PM
|
Replies: 6
Views: 1,178
Re: tan canvas spare tire cover
I have the metal covers and I am going to switch to canvas or vinyl someday because getting the metal ones off is a pain and usually results in scratched paint.
|
Forum: Model A (1928-31)
09-02-2023, 02:58 PM
|
Replies: 6
Views: 761
Re: Cutting spare keys
Dick Crabtree did mine; actually my door lock turned out to be a re-pop and Dick found me an original and keyed my rumble seat lock to match.
|
Forum: Model A (1928-31)
05-29-2023, 01:46 PM
|
Replies: 13
Views: 1,604
Re: Oil Bath air cleaner for the Model A
I sent my Model B carburetor to Renners Garage and David did the necessary machine work to allow use of an air filter.
RENNER'S CORNER
EARLY FORD PARTS
PHONE: 1-734-428-8424
IF WE ARE OUT...
|
Forum: Model A (1928-31)
05-10-2023, 12:30 AM
|
Replies: 7
Views: 1,219
|
Forum: Model A (1928-31)
05-01-2023, 10:50 AM
|
Replies: 12
Views: 2,843
|
Forum: Model A (1928-31)
04-17-2023, 12:30 AM
|
Replies: 20
Views: 2,989
Re: Temperature Gauge Installation
Jim, something you might want to be careful about when running the line through the terminal box and if it is metal. Keep in mind the two screws that hold the cover on are also what the wires hook to...
|
Forum: Model A (1928-31)
04-16-2023, 11:25 AM
|
Replies: 20
Views: 2,989
|
Forum: Model A (1928-31)
04-16-2023, 11:14 AM
|
Replies: 20
Views: 2,989
|
Forum: Model A (1928-31)
04-16-2023, 10:56 AM
|
Replies: 20
Views: 2,989
Re: Temperature Gauge Installation
Mine runs through the terminal box, no drilling required. My gauge is currently a vintage generic brand that looks like a Steward Warner but I have a Boyce Moto Meter from the 30's I believe that...
|
Forum: Model A (1928-31)
04-09-2023, 01:53 PM
|
Replies: 19
Views: 2,156
Re: Snyder’s head question
The Snyder's 6.0 combustion chamber is pretty rough; would there be any benefit to smoothing it up or would that change the volume too much?
|
Forum: Model A (1928-31)
04-09-2023, 01:51 PM
|
Replies: 19
Views: 2,156
|
Forum: Model A (1928-31)
04-07-2023, 02:08 PM
|
Replies: 6
Views: 1,084
|
Forum: Model A (1928-31)
04-06-2023, 12:49 PM
|
Replies: 6
Views: 1,084
Re: Cabriolet screw chart
Snyder's does not list the size or length of the Cabriolet sill plate screws, and they are not specifically for the Cabriolet. The screws that pop up when you pull up the Cabriolet sills specify,...
|
Forum: Model A (1928-31)
04-05-2023, 11:54 PM
|
Replies: 6
Views: 1,084
Re: Cabriolet screw chart
Well after researching the catalog I decided to go onto Snyder's website and look up the Cabriolet Sill Plates and see if it gave a recommendation and a set of (40) 46480-S was the recommendation....
|
Forum: Model A (1928-31)
04-05-2023, 11:17 AM
|
Replies: 6
Views: 1,084
Cabriolet screw chart
Is there a screw chart available that gives locations and size/length of all the screws for a Model A? I have a 1930 Cabriolet and working on switching all the Phillips screws that were used during...
|
Forum: Model A (1928-31)
03-30-2023, 11:32 AM
|
Replies: 30
Views: 7,028
Re: "New" option for turn signals
Jay Leno had a battery powered set on one of his vintage cars but I can't remember which one. The ones he had looked like they were made for the car. I did a little googling but never could find...
|
Forum: Model A (1928-31)
02-21-2023, 01:59 AM
|
Replies: 19
Views: 3,661
Re: Mac's antique auto parts
Back in the Summer I ordered a Cartouche sample card and twice someone tried to contact me to see if they could help me. It seemed strange that just a couple months later they were out of business.
|