Forum: Early V8
10-20-2019, 06:48 PM
|
Replies: 0
Views: 661
46 pickup
I am looking for a heater for 46 Ford truck. Either a complete unit or parts. That would be 6 volt pos. ground. I'll even take any info about where to find info. ...
|
Forum: Early V8 (1932-53)
04-06-2018, 08:07 AM
|
Replies: 7
Views: 1,869
Re: fuel line
Thanks, Your replies are what I suspected, I am using a "Carter" brand pump I got from Mac's. I appreciate the reassurance you guys gave me.
...
|
Forum: Early V8 (1932-53)
04-06-2018, 12:48 AM
|
Replies: 7
Views: 1,869
fuel line
What is the correct route to run a fuel line with mechanical pump and a electric pump? Electric for priming and starting, and the mechanical for running. It's in my 1946 1 ton truck with a V8...
|
Forum: Early V8
01-18-2017, 07:08 PM
|
Replies: 0
Views: 869
|
Forum: Early V8 (1932-53)
12-29-2016, 01:55 AM
|
Replies: 14
Views: 2,588
Re: Local help
I have a 1939-48 Ford manual, I have gotten along ok so far but I need to get my act together.
|
Forum: Early V8 (1932-53)
12-20-2016, 04:20 PM
|
Replies: 14
Views: 2,588
|
Forum: Early V8 (1932-53)
12-20-2016, 04:12 PM
|
Replies: 14
Views: 2,588
Re: Local help
I will search all these tips- Thanks everyone,
Not positive how to reply yet, but I'll get it.
Thanks again..
|
Forum: Early V8 (1932-53)
12-20-2016, 04:01 PM
|
Replies: 14
Views: 2,588
Re: Local help
Alright, armed with this new info I'm ready to go back to it'
|
Forum: Early V8 (1932-53)
12-20-2016, 04:00 PM
|
Replies: 14
Views: 2,588
Re: Local help
Thanks Kerk, That's not too far from where I am. I will look into it.. I don't see the time, but I'll find it. Thanks again!
|
Forum: Early V8 (1932-53)
12-20-2016, 10:09 AM
|
Replies: 14
Views: 2,588
Local help
I'm wondering if anyone knows of a person or place near Framingham Ma. area who could rewire a 46 ford truck ? I've tried-but it makes me crazy.
...
|
Forum: Early V8 (1932-53)
12-15-2016, 04:23 PM
|
Replies: 8
Views: 2,702
Re: Coils
Thanks for the input; that gives me food for thought.
|
Forum: Early V8 (1932-53)
12-15-2016, 11:17 AM
|
Replies: 8
Views: 2,702
Coils
Hi everyone,, Who knows about ignition coils ? I seem to be frying them! I put a PERTONIX IGNITOR electronic ignition with the recomended FLAME-THROWER coil in my 1946 1 ton v8 flathead,it ran for a...
|
Forum: Early V8 (1932-53)
12-12-2016, 08:25 AM
|
Replies: 25
Views: 14,164
|
Forum: Early V8 (1932-53)
11-10-2016, 03:26 PM
|
Replies: 13
Views: 2,587
Re: fan bet help -
I just want to say thanks to all of you for the info, I almost got it right.
|
Forum: Early V8 (1932-53)
11-05-2016, 06:20 PM
|
Replies: 13
Views: 2,587
Re: fan bet help -
Who would you recommend as competent supplier ? Mac's
seems to have gone down hill to the point of no return. I'd like to buy the whole fan hub if I can find it.
|
Forum: Early V8 (1932-53)
11-05-2016, 08:32 AM
|
Replies: 13
Views: 2,587
Re: fan bet help -
The fan belt is fairly loose but the tighter it is, the closer to the bail-wire it is. I am thinking of a wider belt so it don't sit so low in the pulleys. Any thought on that ?
|
Forum: Early V8 (1932-53)
11-04-2016, 06:43 PM
|
Replies: 13
Views: 2,587
fan bet help -
Hi everyone, Could some one explain to me how to adjust the fan beit on my 1946 ford v8 flathead 1 ton truck ? Also the belt itself hits the bail wire that holds the dist.cap on,knocking the cap...
|
Forum: Early V8 (1932-53)
10-19-2016, 07:11 AM
|
Replies: 4
Views: 834
Looking for a solution
I have a 1946 Ford 1 ton , with the lower front mount distributor and the fan belt hits the bail wire that holds the cap in place. Is this a common thing ?(I wouldn't think so) I'll try just about...
|
Forum: Questions & Suggestions
10-19-2016, 07:02 AM
|
Replies: 2
Views: 1,586
|
Forum: Questions & Suggestions
10-18-2016, 06:48 PM
|
Replies: 2
Views: 1,586
Looking for a solution
Hi, I have a little problem, the fan belt on my 1946 v8 flathead knocks off the bail wire that holds the distributor cap on.Then the cap is off ! I had it wired on for a long time but it needs to be...
|