Forum: Model A (1928-31)
12-24-2023, 09:23 AM
|
Replies: 15
Views: 1,261
Re: '31 Tudor Sedan
You might want to check for intake leak if u have a backfire going on
I had what sounds like the same issue and it was intake sucking air by the gasket
Merry Christmas and good luck[emoji1374]
...
|
Forum: Model A (1928-31)
10-28-2023, 05:28 PM
|
Replies: 26
Views: 2,033
Re: Differential Housing Vent
Over thinking it
It vents up thru the torque tube as long as u are still running it
If you are running a open drive shaft
Then yrs you will need an external vent
Sent from my iPhone using...
|
Forum: Model A (1928-31)
10-28-2023, 05:14 PM
|
Replies: 41
Views: 3,122
Re: Hydraulic Brake Conversion
Comman sense
It’s not rocket science
Unless you’re going to use the oem shock mounts
Cut them off and run the backing plates straight up as they were designed
End off issues
Just saying
...
|
Forum: Model A (1928-31)
10-22-2023, 08:23 AM
|
Replies: 8
Views: 1,658
|
Forum: Model A (1928-31)
09-17-2023, 06:33 PM
|
Replies: 15
Views: 1,270
Re: knock during hard acceleration
Why not use a timing light and start playing with it so when your lever is all the down it will only advance as high as 28
Not that hard to do
Sent from my iPhone using Tapatalk
|
Forum: Model A (1928-31)
09-15-2023, 08:07 PM
|
Replies: 62
Views: 6,282
|
Forum: Model A (1928-31)
08-26-2023, 05:53 AM
|
Replies: 5
Views: 674
Re: Spark Gap
Depends on what ignition you are running
Sent from my iPhone using Tapatalk
|
Forum: Model A (1928-31)
08-04-2023, 10:36 AM
|
Replies: 9
Views: 759
Re: iPhone holder for Roadster or Phaeton?
I use a steele other than the magnet on the back of your phone all the time it is great for holding any phone,have one in all my vehicles
Sent from my iPhone using Tapatalk
|
Forum: Model A (1928-31)
08-02-2023, 04:56 PM
|
Replies: 7
Views: 815
|
Forum: Model A (1928-31)
07-06-2023, 12:03 PM
|
Replies: 8
Views: 1,317
Re: 1930 Ford Model A, Acceleration Noise
Sounds like mine under load when not warmed up yet
Hasn’t hurt anything yet, had it all apart this past winter and found nothing out of the ordinary, put it back together and it still makes the...
|
Forum: Model A (1928-31)
07-04-2023, 05:49 AM
|
Replies: 16
Views: 1,650
|
Forum: Model A (1928-31)
05-22-2023, 07:26 PM
|
Replies: 11
Views: 2,138
Re: 1930 model a leaking water
Put a small bottle of K Seal in it if it’s not coming out the over flow k seal will take. Care of what ever leak you may have it is great stuff little pricy but worth it
Sent from my iPhone...
|
Forum: Model A (1928-31)
05-03-2023, 05:06 PM
|
Replies: 16
Views: 2,406
|
Forum: Model A (1928-31)
04-07-2023, 04:39 PM
|
Replies: 11
Views: 1,811
Re: Dipper tray lose
I didn't like the way mine fit so i just brazed mine in place
Good to go ,and now i don't need to be concerned about it!
|
Forum: Model A (1928-31)
03-05-2023, 06:04 PM
|
Replies: 13
Views: 1,891
Split wishbone, pitman inference
https://uploads.tapatalk-cdn.com/20230305/e7529218eb034eb8c83829af198afa89.jpg
Sent from my iPhone using Tapatalkhttps://uploads.tapatalk-cdn.com/20230305/20ca78a742d3a01805192a5cefe86450.jpg
|
Forum: Model A (1928-31)
03-05-2023, 06:02 PM
|
Replies: 13
Views: 1,891
|
Forum: Model A (1928-31)
03-05-2023, 01:28 PM
|
Replies: 13
Views: 1,891
|
Forum: Model A (1928-31)
03-05-2023, 11:13 AM
|
Replies: 13
Views: 1,891
Re: Split wishbone, pitman inference
i used a long pitman arm and bent it two different ways to go around the bone, it works for me but then again i'm using hex bar with heim joints on all my steering i cut the ball off the arm drilled...
|
Forum: Model A (1928-31)
01-20-2023, 12:27 PM
|
Replies: 20
Views: 3,192
|
Forum: Model A (1928-31)
01-20-2023, 12:22 PM
|
Replies: 10
Views: 1,334
|
Forum: Model A (1928-31)
12-25-2022, 04:00 PM
|
Replies: 36
Views: 5,622
|
Forum: Model A (1928-31)
11-10-2022, 08:42 AM
|
Replies: 17
Views: 4,159
|
Forum: Model A (1928-31)
10-09-2022, 12:05 PM
|
Replies: 18
Views: 2,068
|
Forum: Model A (1928-31)
09-15-2022, 12:44 PM
|
Replies: 14
Views: 2,119
|
Forum: Early V8 (1932-53)
09-05-2022, 11:30 AM
|
Replies: 19
Views: 3,775
Re: Moroso Ceramic Sealer
Cerimic seal works great just follow the instructions and you won’t have any problems
Used to use on the race motors i build because of head stud leakage
Amazing stuff if used correctly
...
|