Forum: Early V8 (1932-53)
02-16-2024, 07:10 AM
|
Replies: 21
Views: 2,195
|
Forum: Early V8 (1932-53)
01-10-2024, 07:53 AM
|
Replies: 8
Views: 970
|
Forum: Early V8 (1932-53)
11-30-2023, 08:01 AM
|
Replies: 10
Views: 856
|
Forum: Early V8 (1932-53)
10-24-2023, 06:27 AM
|
Replies: 14
Views: 1,192
|
Forum: Early V8 (1932-53)
04-22-2023, 08:43 AM
|
Replies: 5
Views: 816
|
Forum: Early V8 (1932-53)
04-09-2023, 07:55 AM
|
Replies: 11
Views: 1,332
Re: Converting heater to 12volts
I use one these they work great.
https://vintageautogarage.com/heater-defroster-motor-reducer-12-volt-to-6-volts-100-watts-hr02/
|
Forum: Early V8 (1932-53)
01-21-2023, 07:52 AM
|
Replies: 27
Views: 4,445
|
Forum: Early V8 (1932-53)
12-02-2022, 07:36 AM
|
Replies: 41
Views: 6,711
|
Forum: Early V8 (1932-53)
11-10-2022, 07:04 AM
|
Replies: 27
Views: 4,445
|
Forum: Early V8 (1932-53)
07-23-2022, 02:04 PM
|
Replies: 5
Views: 1,186
|
Forum: Early V8 (1932-53)
08-19-2021, 05:57 AM
|
Replies: 14
Views: 1,841
|
Forum: Early V8 (1932-53)
08-18-2021, 05:50 AM
|
Replies: 14
Views: 1,841
Re: 1939 Mercury Door Garnish Moulding Removal
I've been taking my 39 apart for paint and when I stripped everything off the doors all screws were right there to remove. If your reffering to the straight molding on top of the door then the screws...
|
Forum: Model A (1928-31)
07-22-2021, 06:00 AM
|
Replies: 18
Views: 3,006
Re: 2 Tooth Steering Sector
I bought the worm and shaft combo after reading it could be a bear getting it off. Seems a two arm puller works real well though.
|
Forum: Early V8 (1932-53)
07-20-2021, 06:28 AM
|
Replies: 4
Views: 934
|
Forum: Model A (1928-31)
07-20-2021, 06:20 AM
|
Replies: 18
Views: 3,006
Re: 2 Tooth Steering Sector
I got a sector shaft, steering shaft with worm attached and other box rebuilding parts from Snyders a few weeks ago.
|
Forum: Early V8 (1932-53)
02-28-2021, 09:03 AM
|
Replies: 16
Views: 1,430
|
Forum: Early V8 (1932-53)
02-27-2021, 08:06 AM
|
Replies: 16
Views: 1,430
|
Forum: Early V8 (1932-53)
12-23-2020, 07:21 AM
|
Replies: 7
Views: 1,047
CharlieNY saves the day AGAIN! Another leakless 94
After rebuilding a 94 on a 49 Ford coupe I still had the same leaking carb problem. So I sent it to CharlieNY. He fixed the worn out throttle shaft and replaced the worn out bottom carb base. It's so...
|
Forum: Early V8 (1932-53)
12-02-2020, 07:50 PM
|
Replies: 13
Views: 1,355
Re: Radio antenna location help needed
Rotorwrench. Thanks for posting those links. The pictures on the eBay site cleared up the wire situation. There’s a 5” thin wire on the antenna but a fat wire coming out of the radio. Looks like I...
|
Forum: Early V8 (1932-53)
12-02-2020, 07:40 PM
|
Replies: 13
Views: 1,355
Re: Radio antenna location help needed
Thank you rockfal for taking the time to get those shots. I’d say you have an early radio setup being produced in 1938. Mines different and I have the antenna on the roof in the center right above...
|
Forum: Early V8 (1932-53)
12-02-2020, 12:36 PM
|
Replies: 13
Views: 1,355
Re: Radio antenna location help needed
That would be great! Really need to know where these dang wires are going. I just found one that’s not connected by the back of the radio part in the dash. Any pictures you can get would be...
|
Forum: Early V8 (1932-53)
12-01-2020, 08:12 PM
|
Replies: 13
Views: 1,355
|
Forum: Early V8 (1932-53)
12-01-2020, 04:05 PM
|
Replies: 13
Views: 1,355
Radio antenna location help needed
Hey Everyone,
I'm looking for the radio antenna location on a 39 mercury. I'd imagine it's the same radio used in a Ford. Would it be on the tube box on the firewall or the radio on the dash?...
|
Forum: Early V8 (1932-53)
02-12-2020, 08:58 PM
|
Replies: 15
Views: 2,121
|
Forum: Early V8 (1932-53)
02-12-2020, 01:58 PM
|
Replies: 15
Views: 2,121
5/16" id or 3/8" id fuel hose?
Getting ready to add a fuel pressure regulator to my stock 8ba motor and a 94 EAB carb and will replace all rubber fuel hoses. I have 3/8" from other projects but I'm sure this combination would be...
|