Go Back   The Ford Barn > Search Forums
Reload this Page Search Results

Sponsored Links (Register now to hide all advertisements)

Showing results 1 to 12 of 12
Search took 0.00 seconds. Search: Posts Made By: Easy
Forum: Model A (1928-31) 12-04-2023, 07:52 AM
Replies: 17
Views: 1,212
Posted By Easy
Re: Head/engine pulling adapter and engine stand adapter

Have the Stipe combination head puller/engine lift adapter ,works good.
Forum: Model A (1928-31) 10-16-2023, 06:40 PM
Replies: 25
Views: 1,723
Posted By Easy
Re: Lightened flywheel

Is your crankshaft counter balanced? If not I don’t know if you would want to take weight off the flywheel.
Forum: Model A (1928-31) 10-03-2023, 05:45 AM
Replies: 25
Views: 1,851
Posted By Easy
Re: Head studs

Last I knew the head gasket of choice for the Brumfield head is the Felpro 7013 revision 4. I had a head gasket failure about 5 years ago and replaced it with the Felpro, good so far. Got the gasket...
Forum: Model A (1928-31) 08-18-2023, 06:12 AM
Replies: 9
Views: 959
Posted By Easy
Re: Showroom

The Model A Ford, returning petroleum products to the earth for almost a century!
Forum: Model A (1928-31) 04-08-2023, 06:42 AM
Replies: 13
Views: 2,732
Posted By Easy
Radial tire pressure

What is the recommended pressure to run in the 19 inch American Classic radials?
Forum: Model A (1928-31) 01-31-2023, 02:49 PM
Replies: 8
Views: 1,352
Posted By Easy
Re: I,m back. Been a few years, aviation got in the way!

Tubes for radials also. From Coker.
Forum: Model A (1928-31) 01-31-2023, 01:17 PM
Replies: 8
Views: 1,352
Posted By Easy
I,m back. Been a few years, aviation got in the way!

Just ordered new American Classic radial tires from Coker for my 1930 Tudor. Any pro or con thoughts using radials on the Model A?
Forum: Model A (1928-31) 01-31-2023, 01:10 PM
Replies: 2
Views: 570
Posted By Easy
I,m back. Been a few years, aviation got in the way!

Just ordered new American Classic radial tires from Coker for my 1930 Tudor. Any pro or con thoughts using radials on the Model A?
Forum: Model A (1928-31) 11-01-2019, 05:49 AM
Replies: 33
Views: 5,051
Posted By Easy
Re: Oil for model a+ t

Am I the only one hearing a knock in that engine?
Forum: Model A (1928-31) 04-15-2014, 10:04 PM
Replies: 10
Views: 3,972
Posted By Easy
Re: Front Axle - Repair old or look for replacement?

Concerning how the kingpin holes can get enlarged: It can start to happen after kingpin spindle jobs when the taper pin is inserted and tightened with a wrench instead of hammered in and then...
Forum: Model A (1928-31) 04-15-2014, 08:19 PM
Replies: 10
Views: 3,972
Posted By Easy
Re: Front Axle - Repair old or look for replacement?

My camber came out on the money. I did have the same concern about the 7 degree camber using the hammer method. I was careful to beat an equal amount on the top and bottom bosses. The small amount of...
Forum: Model A (1928-31) 04-14-2014, 08:37 PM
Replies: 10
Views: 3,972
Posted By Easy
Re: Front Axle - Repair old or look for replacement?

I just went through the same axle situation. My axle kingpin holes were very sloppy. After talking with several model A club members they recommended beating the ends of the axle with a shop hammer...
Showing results 1 to 12 of 12

 
Forum Jump
Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:52 PM.