Forum: Model A (1928-31)
09-10-2017, 07:18 PM
|
Replies: 5
Views: 1,075
|
Forum: Model A (1928-31)
08-26-2017, 07:48 PM
|
Replies: 6
Views: 1,695
Re: EvapoRust
Thank you, that is the info I was looking for. The frame is not painted, I can partially see the number, hoping to pull the rest up.
|
Forum: Model A (1928-31)
08-26-2017, 05:14 PM
|
Replies: 6
Views: 1,195
|
Forum: Model A (1928-31)
08-26-2017, 05:13 PM
|
Replies: 6
Views: 1,309
Re: Oil pump
Put a cheap oil pressure gauge on the pump outlet screw. Should answer any questions.
|
Forum: Model A (1928-31)
08-26-2017, 05:10 PM
|
Replies: 3
Views: 1,056
|
Forum: Model A (1928-31)
08-26-2017, 05:05 PM
|
Replies: 5
Views: 973
|
Forum: Model A (1928-31)
08-26-2017, 05:03 PM
|
Replies: 6
Views: 1,695
EvapoRust
I found my Model A serial #. Will EvapoRust remove enough rust to be able to read the numbers. I can almost read them but not entirely.
Thanks for your input.
|
Forum: Model A (1928-31)
08-13-2017, 08:04 PM
|
Replies: 22
Views: 2,717
|
Forum: Model A (1928-31)
08-11-2017, 06:23 PM
|
Replies: 18
Views: 5,437
Re: B Camshaft
How does one tell the difference between A and B distributors?
|
Forum: Model A (1928-31)
08-10-2017, 04:07 PM
|
Replies: 14
Views: 2,175
Re: Installing oil Pan gaskets?
Not sure on the crank seal I THINK you need to trim it to a tad longer and tuck the ends in, some one will chime in on that.
The cork gasket all I do is put some wheel brg grease on the block to...
|
Forum: Model A (1928-31)
07-28-2017, 06:12 PM
|
Replies: 8
Views: 1,439
Re: Door hinge pins
I believe there is a tool specific to that job. Synders has it. A few bucks to save hours of time. Win win for all.
|
Forum: Model A (1928-31)
07-28-2017, 05:50 PM
|
Replies: 8
Views: 1,569
|
Forum: Model A (1928-31)
07-11-2017, 04:11 PM
|
Replies: 18
Views: 6,629
Re: Zenith carb float valve problem
One can also weigh on a mailing scale. If over spec's float is leaking and sinking. I have also reused the orig needle and seat which in my case is steel.
|
Forum: Model A (1928-31)
07-03-2017, 06:04 PM
|
Replies: 34
Views: 7,184
Re: Rod nuts
Just a question........would the oil eventually eat away at the plastic insert?
|
Forum: Model A (1928-31)
07-01-2017, 06:50 PM
|
Replies: 6
Views: 811
|
Forum: Model A (1928-31)
06-30-2017, 07:49 PM
|
Replies: 17
Views: 1,925
Re: Put the oil pan on last night.
My only thought having screwed up oh so many times is, I am glad for you that you saw the pump, running to start it would have been a disaster.
Dont feel bad, we have all been there done that.
|
Forum: Model-A
06-29-2017, 01:03 PM
|
Replies: 0
Views: 1,114
Found these
Ran across a bunch of these today any interest?
http://i462.photobucket.com/albums/qq346/chamokie/Mobile%20Uploads/IMG_0684_zpsfnbqmad7.jpg...
|
Forum: Model A (1928-31)
06-27-2017, 06:55 PM
|
Replies: 24
Views: 5,385
Re: Hershey thoughts.....
This is why it is so important to pass this hobby on to the young. Most will laugh at this but I have had my model A since 1963 when I got out of high school. It still sits out back, obviously in...
|
Forum: Model A (1928-31)
06-25-2017, 06:36 PM
|
Replies: 8
Views: 1,465
|
Forum: Model A (1928-31)
06-25-2017, 10:38 AM
|
Replies: 11
Views: 1,738
|
Forum: Model A (1928-31)
06-24-2017, 01:17 PM
|
Replies: 11
Views: 1,738
Re: Another front drum / brake problem
I would grind down the metal part of the shoe if that is what is hitting on the inner drum.
Make sure ( I am sure you checked) the shoe is firmly planted against the backing plate.
Could be some...
|
Forum: Model A (1928-31)
06-23-2017, 06:36 PM
|
Replies: 43
Views: 7,891
Re: 6 volt Coil problems, I think.
Your test light is acting like a ground. Use a piece of wire to ground dist to block.
If that does not work then run another ground from eng to frame.
|
Forum: Model A (1928-31)
06-21-2017, 07:11 PM
|
Replies: 9
Views: 4,022
Re: Model A ringtone
I have that. My Iphone 6 it was easy.
True story:
After I retired i took a yr off, well that was a yr too long. I am not one to sit around. went to work for a local campground, I was the youngest...
|
Forum: Model A (1928-31)
06-20-2017, 07:32 PM
|
Replies: 43
Views: 7,891
|
Forum: Model A (1928-31)
06-18-2017, 07:29 PM
|
Replies: 49
Views: 10,241
Re: Knock, knock, knock sound
Take a long screw driver to see if you can isolate the noise. If it is the timing gear you will hear it through the screw driver shaft. Or if you have a mechanic's stethoscope that will do the same.
|