Forum: Early V8 (1932-53)
01-20-2024, 07:10 PM
|
Replies: 24
Views: 1,462
Re: 1950 Ford sedan seat too far forward
I’m late seeing this thread, if I remember Correctly you need to remove the bolts that hold the back of the seat on and insert the pins in first, then lean the back forward till the bolt will go back...
|
Forum: Early V8 (1932-53)
11-24-2022, 09:31 PM
|
Replies: 8
Views: 1,246
|
Forum: Early V8 (1932-53)
11-24-2022, 08:16 PM
|
Replies: 8
Views: 1,246
Re: 1950 Ford Heater hose connections
Good job Dan, I was going out to my shop and uncove mine. I've seen several plumbed different than mine, It shouldn't matter which way the water passes through the heater core as long as it flows.
|
Forum: Early V8 (1932-53)
11-24-2022, 07:31 PM
|
Replies: 8
Views: 1,246
|
Forum: Early V8 (1932-53)
11-24-2022, 07:26 PM
|
Replies: 8
Views: 1,246
Re: 1950 Ford Heater hose connections
One hose should go to the heater core and one hose to the control valve, the "u" hose goes between the valve and heater core. If the heater works it's probably right.
|
Forum: Early V8 (1932-53)
08-16-2020, 07:49 PM
|
Replies: 30
Views: 3,528
|
Forum: Early V8 (1932-53)
12-15-2019, 06:05 PM
|
Replies: 41
Views: 9,609
Re: Never rent your car to the studios
There's no way I would loan my car for a movie, I worked to long and hard to get it like it is. I would probably drive it myself if they needed cars on the street, I bet no one on the set would know...
|
Forum: Early V8 (1932-53)
11-16-2019, 09:46 PM
|
Replies: 7
Views: 1,414
|
Forum: Early V8 (1932-53)
10-22-2019, 08:27 PM
|
Replies: 4
Views: 1,231
|
Forum: Early V8 (1932-53)
10-21-2019, 05:08 AM
|
Replies: 3
Views: 1,507
Re: 50 Mercury Heater Fan Squirrel Cage
Is a Ford heater the same? I saw several on eBay last week.
https://www.ebay.com/itm/1950-1951-Ford-Magic-Air-Heater-Assembly-Dated-March-23-1950/352816870742?hash=item5225863556:g:R4oAAOSwECNdBBxB
|
Forum: Early V8 (1932-53)
10-20-2019, 08:18 AM
|
Replies: 26
Views: 4,709
|
Forum: Early V8 (1932-53)
10-19-2019, 06:18 AM
|
Replies: 12
Views: 1,737
|
Forum: Early V8 (1932-53)
10-19-2019, 06:11 AM
|
Replies: 12
Views: 1,737
Re: 50 Ford Fresh Air Vents
No problem, sometimes you have to work with what you have. I've noticed that the heater core still gets warm from heat transfer through the coolant on the return line, that's the reason for dual...
|
Forum: Early V8 (1932-53)
10-18-2019, 07:23 PM
|
Replies: 12
Views: 1,737
|
Forum: Early V8 (1932-53)
10-18-2019, 05:17 AM
|
Replies: 12
Views: 1,737
Re: 50 Ford Fresh Air Vents
On mine I have used the right hole for my fan switch, I installed the same knob on both. I got the push pull switch from NAPA I think.
|
Forum: Early V8 (1932-53)
10-18-2019, 05:14 AM
|
Replies: 12
Views: 1,737
Re: 50 Ford Fresh Air Vents
Correct, I added a heater to mine and now the right vent is controlled by the heater controls, the air passes through the heater coil so it will be warmer than the left. I have bought cut offs to put...
|
Forum: Early V8 (1932-53)
10-17-2019, 07:23 PM
|
Replies: 12
Views: 1,737
|
Forum: Early V8 (1932-53)
10-16-2019, 08:43 PM
|
Replies: 7
Views: 1,740
Re: '50 Ford Overdrive
49 and 50 will interchange, 51 uses the wide mount and The mount is one inch forward on the tail shaft. I installed a 51 od in my 50, had to weld a extension on the mount. If you use a 51 cross...
|
Forum: Early V8 (1932-53)
10-16-2019, 08:32 PM
|
Replies: 2
Views: 911
Re: Ballad of Another Stuck Valve
I replaced a valve, guide and lifter in my 50 a few years back. I hand lapped the valve then filed the stem to get the lash, it's been good so far.
|
Forum: Early V8 (1932-53)
10-10-2019, 07:49 PM
|
Replies: 22
Views: 3,244
|
Forum: Early V8 (1932-53)
09-14-2019, 01:48 PM
|
Replies: 29
Views: 2,837
Re: Overdrive lockout cable on a '51 Ford
Good deal, I just didn’t want you to have to go through what I did, I thought I could simply turn the mount around and it would fit, I was wrong. I had to put the stock 3 speed back in to get the...
|
Forum: Early V8 (1932-53)
09-13-2019, 08:50 PM
|
Replies: 29
Views: 2,837
Re: Overdrive lockout cable on a '51 Ford
I would take measurements from the center of the tunnel to the center of the output shaft and output shaft to the frame just to be safe. Once I figured out I had a 51 od trans and needed to make a...
|
Forum: Early V8 (1932-53)
09-13-2019, 08:38 PM
|
Replies: 29
Views: 2,837
Re: Overdrive lockout cable on a '51 Ford
Tubman are you installing a 51 trans? 49 and 50 use the narrow mount and is about 1-1/2" back towards the tail. I have a 51 trans in mine and had to weld to the 51 mount to use it in the 50.
|
Forum: Early V8 (1932-53)
09-13-2019, 08:31 PM
|
Replies: 29
Views: 2,837
|
Forum: Early V8 (1932-53)
09-13-2019, 08:14 PM
|
Replies: 29
Views: 2,837
|