Forum: Early V8 (1932-53)
04-24-2024, 07:20 AM
|
Replies: 51
Views: 3,639
|
Forum: Early V8 (1932-53)
04-24-2024, 07:17 AM
|
Replies: 51
Views: 3,639
|
Forum: Early V8 (1932-53)
04-24-2024, 04:42 AM
|
Replies: 51
Views: 3,639
|
Forum: Early V8 (1932-53)
04-24-2024, 04:22 AM
|
Replies: 10
Views: 372
|
Forum: Early V8 (1932-53)
04-23-2024, 10:56 PM
|
Replies: 10
Views: 372
Re: No Brake Lights
No……I just made up a 4” wire to connect the two pigtail wires that attach to the master cylinder brake switch. Bang…..the stop lights came on immediately ! Strange !
|
Forum: Early V8 (1932-53)
04-23-2024, 10:32 PM
|
Replies: 10
Views: 372
No Brake Lights
Evening…….all of a sudden I have no brake lights on my ‘40 Sedan. After checking the wiring I made up a jumper wire and plugged into each pig tail wire off the master cylinder brake switch and lights...
|
Forum: Early V8 (1932-53)
07-12-2023, 06:23 AM
|
Replies: 86
Views: 10,726
Re: New project: ‘41 ford pickup
Vanspeed…….you picked a nice place to live ! I’m in Gaylord, Michigan and go that way occasionally. Great drive on the road around the lake. Good luck up there ! I always wanted a ‘40 but could never...
|
Forum: Early V8 (1932-53)
05-15-2023, 01:33 AM
|
Replies: 9
Views: 1,632
Re: carb
I think the attraction is price. Carpenter $500 and Henkyo $139 ! I saw them too, but went with Carpenter. Made in USA and very good quality and very good service.
|
Forum: Early V8 (1932-53)
05-12-2023, 04:46 AM
|
Replies: 12
Views: 4,612
|
Forum: Early V8 (1932-53)
05-11-2023, 01:19 AM
|
Replies: 12
Views: 4,612
|
Forum: Early V8 (1932-53)
05-09-2023, 06:11 AM
|
Replies: 21
Views: 2,075
|
Forum: Early V8 (1932-53)
05-07-2023, 01:54 PM
|
Replies: 21
Views: 2,075
|
Forum: Early V8 (1932-53)
05-07-2023, 11:38 AM
|
Replies: 21
Views: 2,075
Re: '40 Ford Door Closure Mechanism
It’s for sure the spring in remote pivot arm. Got it out and cleaned it all up and found a small piece of spring stuck in the grease. Ugh…..!
|
Forum: Early V8 (1932-53)
05-06-2023, 02:38 PM
|
Replies: 21
Views: 2,075
|
Forum: Early V8 (1932-53)
05-06-2023, 01:21 PM
|
Replies: 21
Views: 2,075
|
Forum: Early V8 (1932-53)
05-05-2023, 09:35 AM
|
Replies: 21
Views: 2,075
|
Forum: Early V8 (1932-53)
05-05-2023, 07:39 AM
|
Replies: 21
Views: 2,075
|
Forum: Early V8 (1932-53)
05-05-2023, 07:28 AM
|
Replies: 21
Views: 2,075
'40 Ford Door Closure Mechanism
Morning....
Had the '40 out yesterday and when I got back home and shut my driver's door I heard something go..."tink" ! Didn't think anything of it until I had to go out again and the door handle...
|
Forum: Early V8 (1932-53)
05-05-2023, 07:21 AM
|
Replies: 12
Views: 1,348
Re: 40 rims and radials?
I bought Coker's for my standard '40 about 10 years ago. I started out tubeless, but then all of a sudden started losing air in a couple of them. I bought radial tubes to match and never had another...
|
Forum: Early V8 (1932-53)
01-30-2023, 05:56 PM
|
Replies: 23
Views: 2,766
|
Forum: Early V8 (1932-53)
10-14-2022, 01:27 PM
|
Replies: 20
Views: 2,926
Re: ‘40 steering box leak
Piston……crawled up the ‘40 today and able to get to the 4 bolts to remove the plate. The info sent from Coop made me feel a hell of a lot better about this. The leak is for sure around the tube as...
|
Forum: Early V8 (1932-53)
10-14-2022, 08:51 AM
|
Replies: 20
Views: 2,926
|
Forum: Early V8 (1932-53)
10-14-2022, 08:50 AM
|
Replies: 20
Views: 2,926
Re: ‘40 steering box leak
Guys this is great thx much ! Appreciate the info and I now understand the tube for horn wire !
Thx again.
Mike
|
Forum: Early V8 (1932-53)
10-12-2022, 02:01 PM
|
Replies: 20
Views: 2,926
Re: ‘40 steering box leak
Seth and Alchemy …… that’s what I’m afraid of ! Something falling out and not being able to reassemble ! I have to think about this. Thx for the info.
Mike
|
Forum: Early V8 (1932-53)
10-11-2022, 07:25 AM
|
Replies: 20
Views: 2,926
Re: ‘40 steering box leak
Oh ….now the bell rings…..I forgot the horn wire runs down the center. I forgot all about that ! Thx …..as of now I know what was meant by welding the tube. I didn’t realize what that meant. Will...
|