Forum: Model A (1928-31)
Today, 04:23 PM
|
Replies: 10
Views: 291
Re: Piston and cylinder clearance / measurement???
This is the best advice. The pistons I got from Snyders had a smaller suggested oversize. I used their specs, and had to pull the engine and have it rebored because it was too tight, overheated, and...
|
Forum: Model A (1928-31)
Today, 04:14 PM
|
Replies: 4
Views: 279
Re: The Perrymobile!
There’s gotta be a set of his original plans somewhere. This is America! Everything is here!
|
Forum: Model A (1928-31)
Today, 12:30 PM
|
Replies: 20
Views: 889
Re: 28 Broadlace trim
I have always liked that little extra touch on the ‘28 interiors, and regret that it wasn’t available for my ‘29s. LeBaron Bonney used to offer it. I wonder if there is any stock left from their...
|
Forum: Model A (1928-31)
Today, 10:57 AM
|
Replies: 4
Views: 279
The Perrymobile!
Another use for these old worn out Model A’s.
https://theoldmotor.com/?p=183187
|
Forum: Model A (1928-31)
Today, 12:57 AM
|
Replies: 20
Views: 521
Re: 32 model b engine
I hope you have a fat wallet! Engine rebuilds cost mucho dinero. Get that B engine as cheap as you can. I would budget at least $4000 from start to finish, and that has to include all the attachments.
|
Forum: Model A (1928-31)
01-22-2021, 09:18 PM
|
Replies: 17
Views: 737
Re: Fact or Fiction: Headlight Lens Gasket
Very interesting. Do you have any information about atmosphere, pollution, and nickel plating? My replated for 15 year (2005) radiator shell is holding up much better than my original plated (1929)...
|
Forum: Model A (1928-31)
01-21-2021, 05:19 PM
|
Replies: 11
Views: 569
|
Forum: Model A (1928-31)
01-21-2021, 05:09 PM
|
Replies: 13
Views: 766
|
Forum: Model A (1928-31)
01-21-2021, 05:07 PM
|
Replies: 13
Views: 766
|
Forum: Model A (1928-31)
01-19-2021, 10:19 PM
|
Replies: 13
Views: 766
Re: “The Restorer” for Jan/Feb 2021
Contrary to Mr. McMimmcs’ statement, there is a very reasonable and logical explanation.
The two magazines are produced and published in different parts of the country with different staff,...
|
Forum: Model A (1928-31)
01-19-2021, 06:48 PM
|
Replies: 13
Views: 766
|
Forum: Model A (1928-31)
01-18-2021, 06:20 PM
|
Replies: 12
Views: 513
|
Forum: Model A (1928-31)
01-17-2021, 11:17 PM
|
Replies: 7
Views: 430
Re: Clutch finger adjustment in car
I did that in my coupe, using a combination square, which allowed me to set the depth at 5/8" and position it over the fingers for adjustment. The hardest part was securing the nuts after adjustment,...
|
Forum: Model A (1928-31)
01-17-2021, 12:14 PM
|
Replies: 35
Views: 2,524
Re: Adding Guages
I have heard that Henry didn’t think a temp gauge was necessary, nor was a motometer, which he resisted offering. His comment, supposedly, was, "Any fool can look out over the hood and see if the...
|
Forum: Model A (1928-31)
01-17-2021, 12:06 PM
|
Replies: 4
Views: 257
|
Forum: Model A (1928-31)
01-16-2021, 10:10 PM
|
Replies: 11
Views: 560
Re: Early '28 Model A - possible AR?
Early ‘28 hoods had an upper slant to the top of the louvers that were not parallel to the hood hinge. Lacing on the radiator shell was threaded into holes in the shell. Most had shrouds on the...
|
Forum: Model A (1928-31)
01-16-2021, 10:02 PM
|
Replies: 20
Views: 609
|
Forum: Model A (1928-31)
01-16-2021, 12:34 AM
|
Replies: 24
Views: 947
Re: Benefits of a thermostat?
Henry hired the best engineers of his time, and I run all my A’s completely stock, so I’ve never seen a need. I trust the engineers, and my cars are still reliable and run well after 92 years. I...
|
Forum: Model A (1928-31)
01-16-2021, 12:11 AM
|
Replies: 25
Views: 1,140
|
Forum: Model A (1928-31)
01-15-2021, 11:15 PM
|
Replies: 20
Views: 609
Re: Won't Start when Warmed Up
That was my problem with my coupe. The clearances mfg specified on current rings and pistons are incorrect for Model A, at least when sleeved back to standard.
|
Forum: Model A (1928-31)
01-14-2021, 04:57 PM
|
Replies: 4
Views: 257
Trunk lid handle not locking
My trunk lid lock has stopped locking. The key still turns and the handle opens and closes properly, but it doesn’t lock. Is there a DIY fix for this or should I just take it to a locksmith? It is...
|
Forum: Model A (1928-31)
01-12-2021, 11:29 PM
|
Replies: 23
Views: 896
Re: AutoLite heater install
That is the best ex. manifold to have. They are more likely not to sag at the rear. Keep it and find a proper Autolite cover for it. Saying that, the hole in your firewall may still be located wrong....
|
Forum: Model A (1928-31)
01-12-2021, 11:25 PM
|
Replies: 6
Views: 566
|
Forum: Model A (1928-31)
01-12-2021, 11:23 PM
|
Replies: 15
Views: 818
|
Forum: Model A (1928-31)
01-10-2021, 12:15 PM
|
Replies: 42
Views: 2,159
|