Forum: Early V8 (1932-53)
Yesterday, 05:48 PM
|
Replies: 20
Views: 634
|
Forum: Early V8 (1932-53)
Yesterday, 01:03 PM
|
Replies: 8
Views: 399
|
Forum: Early V8 (1932-53)
Yesterday, 10:49 AM
|
Replies: 20
Views: 467
|
Forum: Model A (1928-31)
05-13-2024, 08:57 AM
|
Replies: 15
Views: 539
Re: Grease in 2-tooth
Just fill with the same oil you use in transmission and rear axle, they will need to be at least topped up before driving, then you can evaluate for problems, there was usually a reason they were...
|
Forum: Early V8 (1932-53)
05-09-2024, 04:37 PM
|
Replies: 25
Views: 963
Re: Oil leak
How full is the oil, try lowering it to just above add
|
Forum: Early V8 (1932-53)
05-09-2024, 12:47 PM
|
Replies: 17
Views: 666
|
Forum: Model A (1928-31)
05-09-2024, 12:21 PM
|
Replies: 6
Views: 549
|
Forum: Early V8 (1932-53)
05-08-2024, 07:20 PM
|
Replies: 20
Views: 736
Re: Timing gear sheared 12 teeth
Looks like the other areas are mostly chewed through , what condition is the crankshaft gear.
Rough worn crankshaft gear will chew up any timing gear.
Original lifters usually had a hole a pin...
|
Forum: Model A (1928-31)
04-24-2024, 11:54 AM
|
Replies: 31
Views: 2,688
|
Forum: Model A (1928-31)
04-23-2024, 02:36 PM
|
Replies: 26
Views: 2,226
|
Forum: Model A (1928-31)
04-22-2024, 02:16 PM
|
Replies: 29
Views: 2,024
|
Forum: Model A (1928-31)
04-18-2024, 07:49 AM
|
Replies: 7
Views: 744
Re: valve recession
it depends on how recessed the other valves are and as has be mentioned- the form and width of the seats
I have seen them cut so deep that the mushroom on the valve stem was almost gone and the...
|
Forum: Early V8 (1932-53)
04-10-2024, 07:10 PM
|
Replies: 4
Views: 410
|
Forum: Model A (1928-31)
04-10-2024, 07:06 PM
|
Replies: 14
Views: 1,192
|
Forum: Model A (1928-31)
04-10-2024, 08:43 AM
|
Replies: 20
Views: 1,282
|
Forum: Model A (1928-31)
04-06-2024, 09:54 AM
|
Replies: 35
Views: 1,978
Re: Vacuum advance dist. for Model A
you have to be careful with 70s distributors, some have vacuum retard.
some Subaru ones also could be used, all will require modifications to the advance curve
|
Forum: Early V8 (1932-53)
04-05-2024, 11:38 AM
|
Replies: 8
Views: 507
|
Forum: Early V8 (1932-53)
04-05-2024, 11:37 AM
|
Replies: 18
Views: 605
Re: V8 Rear Axle Width
32-34 is the same width as A, the early V8 used the same rear axles as A, later in 32 the banjo was changed to be similar to later banjo’s but is a little more narrow, later gears need some...
|
Forum: Model A (1928-31)
04-05-2024, 11:30 AM
|
Replies: 31
Views: 2,587
|
Forum: Early V8 (1932-53)
04-02-2024, 04:05 PM
|
Replies: 19
Views: 1,245
|
Forum: Early V8 (1932-53)
04-02-2024, 01:14 PM
|
Replies: 96
Views: 6,703
|
Forum: Early V8 (1932-53)
04-02-2024, 08:15 AM
|
Replies: 3
Views: 289
Re: 1936 ford truck rear brake levers
make them , either cored bushing bronze rod and make on lathe for thick bushings or forming flat stock into a bushing and pressing it in then machining to fit.
Ask the places that have NOS parts
|
Forum: Model A (1928-31)
04-02-2024, 08:11 AM
|
Replies: 21
Views: 1,960
|
Forum: Model A (1928-31)
04-02-2024, 06:59 AM
|
Replies: 21
Views: 1,960
Re: How tight should the...
If the balls are not new and round the adjustments should be made turned to lock then adjusted to coil bind of the springs then backed off to cotter hole.
There will be many opinions and some...
|
Forum: Model A (1928-31)
04-02-2024, 06:48 AM
|
Replies: 15
Views: 1,021
Re: bedix???
A weak battery/bad connections can cause those symptoms too
|