Forum: Model A (1928-31)
Today, 08:29 AM
|
Replies: 2
Views: 194
Re: Not A, But Interesting
Interesting video. Well, they did not make 5 million of them.
A while back there was a hulk of a Bugatti car on Bring a Trailer. Too much work and money for me to bring it back. It was bid...
|
Forum: Model A (1928-31)
Today, 07:28 AM
|
Replies: 16
Views: 559
Re: Seized motor/potentially overheated
Do you have the hand crank? Have you tried turning the engine over with the hand crank? What happens if someone pushes in the clutch while you try turning the engine over with the hand crank? That...
|
Forum: Model A (1928-31)
Today, 07:16 AM
|
Replies: 6
Views: 228
Re: Exhaust manifold intake bolts broke
Bob, that is a good idea. In this case, after installing the plug, he could drill and tap the plug using the intake manifold as a drill guide. I would use Loctite or JB Weld to lock the plug in the...
|
Forum: Model A (1928-31)
Today, 07:09 AM
|
Replies: 2
Views: 135
Re: Knocking. Valves?
Could be valves. Could be something else. Try slowing down the engine by retarding the spark. If the noise goes away then the ignition is too far advanced. Or you may be able to better tell where...
|
Forum: Model A (1928-31)
Yesterday, 03:13 PM
|
Replies: 8
Views: 373
Re: Sticking valves?
How many miles on the engine? It may be time for new rings, lapping the valves, and taking up the bearings. Back in the day, this was usually done at around 25,000 miles. It can be done in the car...
|
Forum: Model A (1928-31)
Yesterday, 11:45 AM
|
Replies: 16
Views: 559
Re: Seized motor/potentially overheated
Take the head off or look in the cylinders with a bore scope to see if there is scuffing on the walls. If the pistons get really hot they can expand and scuff. If that does not solve the issue,...
|
Forum: Model A (1928-31)
Yesterday, 11:29 AM
|
Replies: 6
Views: 228
Re: Exhaust manifold intake bolts broke
A new or used (in good shape) exhaust manifold is what I would chose. If you want to repair that manifold, it will need to be welded up and re drilled and re tapped. I don't think a Helicoil is...
|
Forum: Model A (1928-31)
05-01-2024, 11:35 AM
|
Replies: 11
Views: 492
Re: radiator splashing
I use an extra thick O ring on my radiator cap to seal it and keep the coolant from splashing out. The water pump impeller can push extra coolant when you rev the motor to down shift. Or, as Canton...
|
Forum: Model A (1928-31)
05-01-2024, 06:07 AM
|
Replies: 9
Views: 463
Re: Hole inside front block
I remember reading that the hole was broken through with a hammer after the block was cast and that is the reason it is so rough.
|
Forum: Model A (1928-31)
05-01-2024, 06:01 AM
|
Replies: 11
Views: 514
Re: Head stud to block
The Helicoil will work just fine. It will provide more pull out strength than the original threaded hole. Only one thing to watch out for and that is the accuracy of drilling the hole for the tap...
|
Forum: Model A (1928-31)
04-30-2024, 11:10 AM
|
Replies: 13
Views: 659
Re: 30 Model A engine rebuild
Rusty, What are you planning to do with your car? If you are planning to use it a lot and drive across the country and keep it for decades, then you should consider the Burtz block. If you are...
|
Forum: Model A (1928-31)
04-30-2024, 07:52 AM
|
Replies: 21
Views: 800
Re: new guy, old car
One other piece of advice: Add the fuse that mounts next to the starter switch. That will protect you from an electrical fire.
|
Forum: Model A (1928-31)
04-29-2024, 07:11 PM
|
Replies: 13
Views: 1,011
Re: Henry and Edsel
Henry has been blamed for Edsel's early death. But I think Edsel's lifestyle had something to do with it.
|
Forum: Model A (1928-31)
04-29-2024, 05:58 PM
|
Replies: 2
Views: 221
Re: Does it matter - Tie Rod Direction
What was wrong with the old ends? Can't the pads just be replaced?
Unless you are having the car judged, what is wrong with the grease fittings being in front, or what is wrong with turning the...
|
Forum: Model A (1928-31)
04-29-2024, 05:36 PM
|
Replies: 21
Views: 800
Re: new guy, old car
Ole Thirty, You are doing all the right stuff and it sounds like you have the mechanical skill to work on this car. As you say, it is nice and easy to work on.
Change all the fluids. Use a...
|
Forum: Model A (1928-31)
04-29-2024, 09:18 AM
|
Replies: 20
Views: 974
|
Forum: Model A (1928-31)
04-29-2024, 07:39 AM
|
Replies: 21
Views: 984
Re: Interested Dash information
Wick, those are the wrong kind of matches. One would have to use the "strike anywhere" kind that had two colors on the tips. I am not sure if they are available anymore.
Regarding leaking...
|
Forum: Model A (1928-31)
04-29-2024, 07:24 AM
|
Replies: 8
Views: 371
Re: Float A Motor
Several members have reported that the stock setup in the front works better than any of the aftermarket mounts.
|
Forum: Model A (1928-31)
04-28-2024, 09:03 AM
|
Replies: 4
Views: 479
|
Forum: Model A (1928-31)
04-27-2024, 06:03 PM
|
Replies: 18
Views: 1,063
Re: Distributor wiring
The original configuration was made to discourage theft. The distributor had to pulled from the engine to unscrew the armored cable. Without the pop-out ignition switch popped out the wire to the...
|
Forum: Model A (1928-31)
04-27-2024, 05:53 PM
|
Replies: 15
Views: 1,058
The Old Motor
There is a neat photo of a Model A pickup in the latest edition of The Old Motor, see https://theoldmotor.com/?p=157396. I would publish the photo here but I am not sure of the copyright issues.
...
|
Forum: Model A (1928-31)
04-27-2024, 09:18 AM
|
Replies: 26
Views: 1,930
|
Forum: Model A (1928-31)
04-27-2024, 08:57 AM
|
Replies: 17
Views: 1,133
Re: Batteries completely discharging
Installing a battery cutoff switch is a good idea for two reasons: It will eliminate any drain on the battery when the car sits. It is also a safety item in case there is an electrical fire.
...
|
Forum: Model A (1928-31)
04-27-2024, 08:45 AM
|
Replies: 20
Views: 974
|
Forum: Model A (1928-31)
04-19-2024, 07:15 AM
|
Replies: 13
Views: 2,425
Re: Stipe Machine/Specialty Motor Cams
Dodge, If you make cam cores, make them with 5 bearings. That way they will work in the Burtz block. Not that the 3 bearing cams will not work but that the 5 bearing cams take advantage of the 5...
|