Forum: Early V8 (1932-53)
04-22-2024, 03:36 PM
|
Replies: 14
Views: 586
Re: Oil Filter Canister Question
Tim, doe the nipple that goes into the canister have the restrictive .060 hole? Otherwise were would it be? The T that I have is not that small. Thanks.
|
Forum: Early V8 (1932-53)
04-22-2024, 03:32 PM
|
Replies: 14
Views: 586
|
Forum: Early V8 (1932-53)
04-20-2024, 07:33 PM
|
Replies: 14
Views: 586
Re: Oil Filter Canister Question
Thanks guys for the responses. The label on the nos canister could explain the differences perhaps? I'd like to use this canister because the IN port is larger and I can fit the brass T pictured. I...
|
Forum: Early V8 (1932-53)
04-20-2024, 11:46 AM
|
Replies: 14
Views: 586
Oil Filter Canister Question
Looking over a couple canisters that I have, I noticed that some had a "spacer" at the bottom of the tube and a spring/washer on the cover, both are not removable. Looking at an NOS canister (got...
|
Forum: Early V8 (1932-53)
04-17-2024, 10:15 AM
|
Replies: 69
Views: 26,591
|
Forum: Early V8 (1932-53)
04-16-2024, 09:41 AM
|
Replies: 12
Views: 917
|
Forum: Early V8 (1932-53)
04-16-2024, 09:29 AM
|
Replies: 7
Views: 504
|
Forum: Early V8 (1932-53)
04-16-2024, 09:21 AM
|
Replies: 50
Views: 1,866
|
Forum: Early V8 (1932-53)
04-15-2024, 09:32 AM
|
Replies: 7
Views: 504
|
Forum: Early V8 (1932-53)
04-14-2024, 09:04 AM
|
Replies: 7
Views: 504
Re: '51 o/d cable holder
Tim, if you do have one I would be grateful if I could get that from you for whatever you need for it. Thanks.
|
Forum: Early V8 (1932-53)
04-13-2024, 06:08 PM
|
Replies: 7
Views: 504
'51 o/d cable holder
My '51 Tudor was not an O/D car originally but it is getting one now after Mac Vanpelt built me a trans. One piece I am lacking is the bracket or holder that secures the cable housing from moving at...
|
Forum: Early V8 (1932-53)
04-12-2024, 02:54 PM
|
Replies: 7
Views: 373
Re: Oil Pressure Sender... 6v & 12v
Thanks for the responses guys. I figured this was a no go. I'll have to decide which oil pressure gauge I want to rely on, the original or the under dash Stewart Warner for which I do have a matching...
|
Forum: Early V8 (1932-53)
04-12-2024, 01:51 PM
|
Replies: 1
Views: 145
|
Forum: Early V8 (1932-53)
04-11-2024, 08:56 PM
|
Replies: 7
Views: 373
Oil Pressure Sender... 6v & 12v
My '51 Tudor project continues, converted to 12v neg. ground but voltage reducer to fuel, temp, and oil pressure gauges. I have an under dash gauge cluster for 12v temp and oil pressure, both are...
|
Forum: Early V8 (1932-53)
03-30-2024, 10:48 AM
|
Replies: 11
Views: 1,080
Re: Leaking Head Studs
"I drained the coolant and refilled with distilled water, then put in a bottle of 2-part Rislone Cooling System Repair, and ran it for about 15 minutes."
So, are we to assume this fixed your...
|
Forum: Early V8 (1932-53)
03-09-2024, 09:11 AM
|
Replies: 27
Views: 1,365
Re: Installing a wiring harness
"Will I have to remove any more of the interior to get the wires to the back of the car for the taillights?"
I recently rewired my '51 Tudor and the back wires went up the A pillar, above the...
|
Forum: Early V8 (1932-53)
03-06-2024, 11:05 AM
|
Replies: 13
Views: 633
|
Forum: Early V8 (1932-53)
02-18-2024, 09:00 AM
|
Replies: 31
Views: 2,224
|
Forum: Early V8 (1932-53)
02-17-2024, 09:17 AM
|
Replies: 31
Views: 2,224
|
Forum: Early V8 (1932-53)
02-07-2024, 10:58 AM
|
Replies: 5
Views: 477
|
Forum: Early V8 (1932-53)
01-23-2024, 12:05 PM
|
Replies: 29
Views: 1,831
|
Forum: Early V8 (1932-53)
01-11-2024, 12:47 PM
|
Replies: 9
Views: 516
Re: Side molding for 1950 Ford 2 door sedan
Are you planning on painting the car either way? Would be a lot of work just to deal with filling trim holes. Would suggest calling Chris at 610-442-2187 afternoons, as he has probably 30 '49 - '51...
|
Forum: Early V8 (1932-53)
01-10-2024, 10:05 AM
|
Replies: 25
Views: 1,754
|
Forum: Early V8 (1932-53)
01-05-2024, 02:51 PM
|
Replies: 3
Views: 573
Re: Mad electrical
I did call Mark, and ended up talking to him for about 30 min! He's still in business but on a smaller scale, one can order by phone. He has an incredible memory, asking me about one of my projects...
|
Forum: Early V8 (1932-53)
01-04-2024, 06:45 PM
|
Replies: 3
Views: 573
Mad electrical
Over the last 15 years I have bought a lot of high quality electrical stuff from Mark at MAD ELECTRICAL, usually over the phone. He is a chatty but really nice guy. Anyway just wondering if anyone...
|