Forum: Early V8 (1932-53)
05-19-2024, 11:17 AM
|
Replies: 9
Views: 691
|
Forum: Early V8 (1932-53)
05-15-2024, 03:25 PM
|
Replies: 316
Views: 20,411
Re: 276 stroker from 35 years of parts
This would explain why you are getting such tight clearances. I don't know that I have ever had that happen in one of my engines. Perhaps the block has been decked?
|
Forum: Early V8 (1932-53)
05-15-2024, 10:33 AM
|
Replies: 316
Views: 20,411
|
Forum: Early V8 (1932-53)
05-14-2024, 09:53 PM
|
Replies: 316
Views: 20,411
|
Forum: Early V8 (1932-53)
05-11-2024, 10:12 AM
|
Replies: 316
Views: 20,411
Re: 276 stroker from 35 years of parts
On my pump test stand, I have a valve to shut off flow and test relief valve pressure. I restrict the flow to 40 psi back pressure and check flow rate. Typically 1.5 gpm.
|
Forum: Early V8 (1932-53)
05-10-2024, 10:30 PM
|
Replies: 29
Views: 1,087
Re: 37 coupe RTS T-170 swap!
I did the swap to my 39 30 years ago. Used a Bronco 9" with 3.70 gears. Does 73 mph at 2500 rpm. i did mine with the body off.
|
Forum: Early V8 (1932-53)
05-10-2024, 11:08 AM
|
Replies: 16
Views: 680
|
Forum: Early V8 (1932-53)
04-25-2024, 12:02 PM
|
Replies: 316
Views: 20,411
|
Forum: Early V8 (1932-53)
04-18-2024, 09:02 PM
|
Replies: 316
Views: 20,411
|
Forum: Early V8 (1932-53)
04-17-2024, 09:02 PM
|
Replies: 316
Views: 20,411
|
Forum: Early V8 (1932-53)
04-15-2024, 09:58 PM
|
Replies: 50
Views: 2,187
|
Forum: Early V8 (1932-53)
04-11-2024, 04:58 PM
|
Replies: 48
Views: 3,109
|
Forum: Early V8 (1932-53)
04-11-2024, 10:53 AM
|
Replies: 48
Views: 3,109
|
Forum: Early V8 (1932-53)
04-10-2024, 10:30 PM
|
Replies: 48
Views: 3,109
Re: NOS 8RT camshaft
In this case the follower is the lifter. i use an adjustable lifter and set it so the valve is off the seat.
|
Forum: Early V8 (1932-53)
04-10-2024, 10:01 AM
|
Replies: 48
Views: 3,109
|
Forum: Early V8 (1932-53)
04-09-2024, 10:14 AM
|
Replies: 96
Views: 6,766
|
Forum: Early V8 (1932-53)
04-08-2024, 10:14 PM
|
Replies: 96
Views: 6,766
|
Forum: Early V8 (1932-53)
04-07-2024, 11:24 AM
|
Replies: 96
Views: 6,766
|
Forum: Early V8 (1932-53)
03-26-2024, 09:55 AM
|
Replies: 316
Views: 20,411
|
Forum: Early V8 (1932-53)
03-24-2024, 03:34 PM
|
Replies: 316
Views: 20,411
|
Forum: Early V8 (1932-53)
03-23-2024, 09:36 PM
|
Replies: 10
Views: 534
|
Forum: Early V8 (1932-53)
03-23-2024, 09:29 PM
|
Replies: 316
Views: 20,411
|
Forum: Early V8 (1932-53)
03-20-2024, 09:29 PM
|
Replies: 96
Views: 6,766
|
Forum: Early V8 (1932-53)
03-20-2024, 09:25 PM
|
Replies: 9
Views: 753
Re: Front seals
I have installed many 1 piece seals on my builds and have yet to have a problem, even with the stock spiral sleeve.
|
Forum: Early V8 (1932-53)
03-20-2024, 10:05 AM
|
Replies: 9
Views: 753
Re: Front seals
Was the seal installed properly? If you are not careful, the seal lip can roll under.
|