Forum: Early V8 (1932-53)
12-20-2020, 12:00 AM
|
Replies: 6
Views: 1,023
Re: 46 ford misfire
I’d replace the condenser 1st. Cheap and easy. Sounds like a similar situation I had some years ago.
|
Forum: Early V8 (1932-53)
12-18-2020, 01:44 PM
|
Replies: 10
Views: 1,657
Re: Internal Breather Tube
Here's a link to my post about why I NEEDED one.
https://www.fordbarn.com/forum/showthread.php?t=290768
|
Forum: Early V8 (1932-53)
12-18-2020, 01:17 PM
|
Replies: 10
Views: 1,657
Re: Internal Breather Tube
You can try an ad in the "parts wanted" section of this forum, but be aware that the scammers watch it big time. I did, and immediately had three responses from scammers.....they are easy to spot!
|
Forum: Early V8 (1932-53)
12-15-2020, 08:58 PM
|
Replies: 10
Views: 1,657
Re: Internal Breather Tube
I have one.....what’s your address.
PM me.....I’ll ship it in the morning...free. A couple of guys on here did the same for me a couple of weeks ago and I ended up with an extra.
|
Forum: Early V8 (1932-53)
12-07-2020, 11:52 PM
|
Replies: 4
Views: 819
Re: Oil drip off of starter
Its on the right(passenger) side. It’s a truck pan with a clean out. I didn’t know that it’s on the opposite side from normal......interesting
|
Forum: Early V8 (1932-53)
12-07-2020, 10:56 PM
|
Replies: 4
Views: 819
Re: Oil drip off of starter
I think I figured it out.
Before I installed a pcv valve I did have a small bit of oil coming out of the dipstick tube around the dipstick after hard highway runs. I was constantly wiping residual...
|
Forum: Early V8 (1932-53)
12-07-2020, 09:50 PM
|
Replies: 4
Views: 819
Oil drip off of starter
I have one slight oil leak on my flathead....just a few small drops of motor oil coming from the tip of my starter. It’s not coming from above the starter. I first thought it was coming from the...
|
Forum: Early V8 (1932-53)
12-06-2020, 06:23 PM
|
Replies: 51
Views: 7,514
|
Forum: Early V8 (1932-53)
12-05-2020, 07:12 PM
|
Replies: 51
Views: 7,514
Re: “Inside” part of road draft tube
All I know is that it works. The Max1 is not a radical cam.
There may be a valve that “fits” better, but I’m pleased.
If you know of a better pcv valve for my engine, give me a part # please........
|
Forum: Early V8 (1932-53)
12-05-2020, 07:02 PM
|
Replies: 51
Views: 7,514
|
Forum: Early V8 (1932-53)
12-05-2020, 05:33 PM
|
Replies: 51
Views: 7,514
Re: “Inside” part of road draft tube
Finished the pcv valve install last night.
Installed the tube beneath the manifold. Drilled and tapped the manifold at the road draft tube location and the carb block off plate for 1/4” pipe thread...
|
Forum: Early V8 (1932-53)
12-02-2020, 08:08 AM
|
Replies: 51
Views: 7,514
|
Forum: Early V8 (1932-53)
12-01-2020, 10:26 PM
|
Replies: 51
Views: 7,514
Re: “Inside” part of road draft tube
This particular valve is a Borg Warner PV255. It is built to use horizontally. Same valve that’s used on the road draft tube of a mid-late 60s SBC. 1/4” pipe thread on block end.
Hope it works well....
|
Forum: Early V8 (1932-53)
12-01-2020, 09:55 PM
|
Replies: 51
Views: 7,514
Re: “Inside” part of road draft tube
Once I find out how well it works, I’ll change the rubber line to copper.
I should have the tube that goes under the manifold by the weekend.
Thanks for everyone’s help.
Norris
Then I’ll get...
|
Forum: Early V8 (1932-53)
11-28-2020, 03:18 PM
|
Replies: 51
Views: 7,514
Re: “Inside” part of road draft tube
Thanks Merc! I’ve seen those before! I think I can easily perform that minor surgery on my Navarro.
Thanks so much for your assistance!
Maybe with that modification I can run one vacuum fitting...
|
Forum: Early V8 (1932-53)
11-28-2020, 02:03 PM
|
Replies: 51
Views: 7,514
Re: “Inside” part of road draft tube
I’m running the two end carbs....center is blocked off. It runs much better running the two end carbs directly connected to each other than with 3 running progressive. I can, at this point easily add...
|
Forum: Early V8 (1932-53)
11-28-2020, 11:44 AM
|
Replies: 51
Views: 7,514
Re: “Inside” part of road draft tube
Hey Merc!
What if I cut a 3/8” or so 1/2” deep slot between the two holes where the carb would go (which now has a block off plate)to join the left and right plenum. The left and right plenums are...
|
Forum: Early V8 (1932-53)
11-28-2020, 09:54 AM
|
Replies: 51
Views: 7,514
|
Forum: Early V8 (1932-53)
11-28-2020, 03:29 AM
|
Replies: 51
Views: 7,514
Re: “Inside” part of road draft tube
That’s where I’ve decided to put a pcv valve. The way my manifold is designed, I’m going to need to pickup vacuum from each side of the manifold.....so I don’t lean out any cylinders. I don’t really...
|
Forum: Early V8 (1932-53)
11-27-2020, 10:32 PM
|
Replies: 51
Views: 7,514
Re: “Inside” part of road draft tube
Special thanks to Mark, Bob and Richard.......I have had offers from all three to send me the tube I need!
Great bunch of guys on this forum!
I’m looking forward to “paying it forward”
Norris
...
|
Forum: Early V8 (1932-53)
11-27-2020, 04:00 PM
|
Replies: 51
Views: 7,514
Re: “Inside” part of road draft tube
Thanks 1940.....I'll look into that also.
Wayne at Dennis Carpenter says they have one in a NOS part #! I can't order it until Monday because they are running a short crew today(understandable)....
|
Forum: Early V8 (1932-53)
11-27-2020, 03:25 PM
|
Replies: 51
Views: 7,514
|
Forum: Early V8 (1932-53)
11-27-2020, 09:20 AM
|
Replies: 51
Views: 7,514
|
Forum: Early V8 (1932-53)
11-26-2020, 10:50 PM
|
Replies: 51
Views: 7,514
|
Forum: Early V8 (1932-53)
11-26-2020, 10:08 PM
|
Replies: 51
Views: 7,514
Re: “Inside” part of road draft tube
Thanks.....I don’t, but can probably find that piece and build one if I have to.
I would not have known that if you hadn’t brought it to my attention!
|