Forum: Early V8 (1932-53)
09-12-2022, 09:42 AM
|
Replies: 0
Views: 349
1936 Pickup Fender Contour
Looking for information on front fender contour on a 1936 pickup. Does anyone have a good fender that they could trace off the front 16-18 inches of the flange that ultimately attaches to the...
|
Forum: Early V8 (1932-53)
08-29-2022, 10:55 AM
|
Replies: 1
Views: 608
Re: 1935 Pickup Fender Support
Here's a photo of the secondary front fender supports for the 1936 Pickup, that I'm working on. From end-to-end, the measure about 10-3/4". The should be the same as the 1935 Ford.
|
Forum: Early V8 (1932-53)
08-20-2022, 01:06 PM
|
Replies: 4
Views: 867
1936 Grille and Windshield Paint
Most of the windshield frames I see at car shows are chromed. I assume this was not the standard practice during manufacture. The windshield on my 1936 Pickup was apparently not chromed. Were...
|
Forum: Early V8 (1932-53)
07-29-2022, 09:34 AM
|
Replies: 2
Views: 509
Re: 36 Pickup Front Fender Alignment
Thanks Jeff, The truck I'm working with has had poor repair work to both front fenders that I'm currently trying to correct. The better grille I have is 18.5 inch wide and was hoping it was correct.
|
Forum: Early V8 (1932-53)
07-22-2022, 12:09 PM
|
Replies: 2
Views: 509
36 Pickup Front Fender Alignment
Hey Guys, Can someone shoot me a representative flange to flange measurement at the base of their 1936 pickup radiator shell, (or flange to flange between front fenders where they meet the lower...
|
Forum: Early V8 (1932-53)
06-27-2022, 10:04 AM
|
Replies: 11
Views: 881
Re: 1936 Pickup Grille Dimensions
Model 51 - Yes, I have the holes on the inner edge where the stainless trim would attached.
oldandtired - The grille pan attachment holes, on the bottom of the chin, are indicated on the drawing...
|
Forum: Early V8 (1932-53)
06-26-2022, 06:39 PM
|
Replies: 11
Views: 881
1936 Pickup Grille Dimensions
I have a couple of 1936 Ford Pickup grille shells. One is a complete shell with grille, but it's got some metal damage on the lower portion of the shell. The other appears descent but someone had...
|
Forum: Early V8
10-16-2021, 07:03 PM
|
Replies: 0
Views: 433
|
Forum: Early V8 (1932-53)
09-18-2021, 11:50 AM
|
Replies: 6
Views: 919
Re: 1936 1/2 ton
My thanks also! Not ready for the box yet, but had been puzzling about where these blocks were installed.
|
Forum: Early V8 (1932-53)
09-09-2021, 06:39 PM
|
Replies: 1
Views: 676
Cab to frame webbing
What are others currently using between the frame, wood supports and cab on mid-30's pickups? My 1936 pickup had rectangular pieces of canvas webbing material between these components. It appears...
|
Forum: Early V8 (1932-53)
08-31-2021, 02:33 PM
|
Replies: 12
Views: 2,043
Re: What Fender?
Well, they'd probably be worth more if they were from a Binder.
|
Forum: Early V8 (1932-53)
08-30-2021, 01:04 PM
|
Replies: 12
Views: 2,043
Re: What Fender?
Still looking for some consensus on these fenders. Here are a couple more photos.
Front of the fender has one level of 3 holes on 3-1/2" centers and a lower level of 2 holes on 5" centers. ...
|
Forum: Early V8 (1932-53)
08-29-2021, 04:04 PM
|
Replies: 12
Views: 2,043
What Fender?
Have a bit on a dilemma. Bought a 1936 Ford Pickup years ago and am just now starting to reassemble. The truck appeared to be complete, except no engine/transmission. However, I have come to...
|
Forum: Early V8 (1932-53)
08-25-2021, 10:26 AM
|
Replies: 26
Views: 4,529
Re: 1936 pickup cab corner question
A little late to this inquiry, but ran into a guy at a swap meet last weekend and we were both in need of rear cap corners. Maybe whoever has the tooling will eventually catch on that there's a...
|
Forum: Early V8 (1932-53)
08-16-2021, 08:07 PM
|
Replies: 70
Views: 13,649
|
Forum: Early V8 (1932-53)
08-16-2021, 07:59 PM
|
Replies: 41
Views: 5,250
|
Forum: Early V8 (1932-53)
08-16-2021, 07:42 PM
|
Replies: 3
Views: 688
|
Forum: Early V8 (1932-53)
08-16-2021, 07:39 PM
|
Replies: 18
Views: 2,606
Re: 36 Car Headlight Buckets
Where is the correct measurement made to determine the diameter of '35-'36-'37 Pickup headlight buckets? Or do you just measure the diameter of the lense?
|
Forum: Early V8 (1932-53)
08-16-2021, 07:20 PM
|
Replies: 2
Views: 679
One more '36 Pickup
Bought the truck 35+ years ago and tore it apart to have some body work done. Then life went forward and the truck sat in an old barn. Now I'm trying to figure out how some various components bolt...
|
Forum: Early V8 (1932-53)
08-16-2021, 05:39 PM
|
Replies: 5
Views: 995
Re: remember when
It's really tough to come up with parts for anything. Not that the Made in China parts are necessarily bad, but you typically have to do some drilling, filing or other modification to make them...
|
Forum: Early V8 (1932-53)
08-16-2021, 05:02 PM
|
Replies: 3
Views: 724
Re: 39 pickup bed
You might want to check-out Mack Products out of Moberly, Missouri, (mack-products.com). I intend to get a new bed from them in the future. I believe they may be the manufacturer for several of the...
|
Forum: Early V8 (1932-53)
08-12-2021, 10:40 AM
|
Replies: 3
Views: 501
1936 Ford Pickup Radiator
Can someone clue me in on the original radiator core thickness for a 1936 pickup? The radiator is gone, but mounting bracket is still around. Based on the bracket, this truck had a 3.25" thick...
|
Forum: Early V8 (1932-53)
07-31-2021, 04:39 PM
|
Replies: 4
Views: 876
Re: 1936 Ford Pickup Fender Braces
Here is a photo of the rear fender bracket I received. It's sitting atop a 12" square. My fender width is 10.5", while this bracket is 12" wide. What am I missing?
Thanks
|
Forum: Early V8 (1932-53)
07-30-2021, 03:27 PM
|
Replies: 4
Views: 876
1936 Ford Pickup Fender Braces
Hey Guys,
I've got a 1936 Ford Pickup that I probably bought 40 years ago and tore-down 30+ years ago. I bought one new front fender brace and a pair of rear fender braces from Early Ford V8 (SC). ...
|