Forum: Model A (1928-31)
Yesterday, 12:13 PM
|
Replies: 7
Views: 378
Re: Winfield Model M updraft carb
The difference between the S and the SR is that the later has an accelerator pump, not needed IMO. Gasket sets are available. Price depends on size, condition and are they complete with air-horn or...
|
Forum: Model A (1928-31)
04-27-2024, 11:36 AM
|
Replies: 7
Views: 638
Re: Side Water Outlet
The diamond is a genuine Ford part but cast by an outside foundry. That mark can be found on many Ford parts.
|
Forum: Model A (1928-31)
04-27-2024, 11:33 AM
|
Replies: 7
Views: 378
Re: Winfield Model M updraft carb
They were only used on T's. They are better than the stock T carb, but IMO a bit small for the Model A. I've run a few Winfield model S on my warmed up Model A, and really like them.
|
Forum: Model A (1928-31)
04-25-2024, 01:12 PM
|
Replies: 26
Views: 1,717
|
Forum: Model A (1928-31)
04-24-2024, 11:22 AM
|
Replies: 26
Views: 1,717
|
Forum: Model A (1928-31)
04-22-2024, 11:43 AM
|
Replies: 1,411
Views: 323,992
|
Forum: Model A (1928-31)
04-21-2024, 12:47 PM
|
Replies: 13
Views: 2,364
|
Forum: Model A (1928-31)
04-18-2024, 11:08 AM
|
Replies: 13
Views: 2,364
|
Forum: Model A (1928-31)
04-17-2024, 11:48 AM
|
Replies: 2
Views: 412
|
Forum: Model A (1928-31)
04-17-2024, 11:46 AM
|
Replies: 13
Views: 2,364
|
Forum: Model A (1928-31)
04-17-2024, 11:45 AM
|
Replies: 7
Views: 614
|
Forum: Model A (1928-31)
04-13-2024, 11:23 AM
|
Replies: 2
Views: 404
|
Forum: Model A (1928-31)
04-13-2024, 11:20 AM
|
Replies: 18
Views: 865
|
Forum: Model A (1928-31)
04-13-2024, 11:09 AM
|
Replies: 4
Views: 299
Re: '31 pickup rear fender filler panels
If yours is a late '31, it has narrower fenders and no fill panel. Late 31's have the fuel shut-off on the front side of the firewall, a dropped steering support, not attached to the gas tank, and a...
|
Forum: Late V8 (1954+)
04-12-2024, 11:11 AM
|
Replies: 0
Views: 290
Antique Nationals
Irwindale Raceway has postponed the Antique Nationals until May 26th due to pending rain. The new date is 5-26-24
|
Forum: Early V8 (1932-53)
04-12-2024, 11:10 AM
|
Replies: 1
Views: 207
Antique Nationals
Irwindale Raceway has postponed the Antique Nationals until May 26th due to pending rain. The new date is 5-26-24
|
Forum: Model T (1909-1927)
04-12-2024, 11:09 AM
|
Replies: 0
Views: 278
ntique Nationals
Irwindale Raceway has postponed the Antique Nationals until May 26th due to pending rain. The new date is 5-26-24
|
Forum: Model A (1928-31)
04-12-2024, 11:05 AM
|
Replies: 2
Views: 404
Antique Nationals
Irwindale Raceway has postponed the Antique Nationals until May 26th due to pending rain. The new date is 5-26-24
|
Forum: Model A (1928-31)
04-07-2024, 12:13 PM
|
Replies: 1,411
Views: 323,992
Re: tell a Model A related story
I mow with a 601 Ford tractor and tow a brand X mower. Both are old and worn out, like me, but they still work. I used to maintain our road with the tractor and a 7' blade but a neighbor does most...
|
Forum: Model A (1928-31)
04-06-2024, 12:16 PM
|
Replies: 5
Views: 577
Re: Model A hubs on V8 Axle?
Yes they can but the only advantage is the spring mounting. You can just make a bolt-on bracket to accomplish this.
|
Forum: Model A (1928-31)
04-06-2024, 12:11 PM
|
Replies: 35
Views: 1,746
Re: Vacuum advance dist. for Model A
For a dist with vacuum advance you will need a carb wit a port for that, most vacuum dists don't use manifold vacuum. I doubt if there would be enough improvement to notice?
|
Forum: Model A (1928-31)
04-01-2024, 01:30 PM
|
Replies: 2
Views: 249
|
Forum: Model A (1928-31)
03-31-2024, 12:18 PM
|
Replies: 15
Views: 1,113
|
Forum: Model A (1928-31)
03-30-2024, 11:01 AM
|
Replies: 15
Views: 1,113
Re: Revised "Builders Guide"
I too recommend a steel crank gear. I broke a brand new cast iron gear while racing at Bonneville. An aluminum cam gear is very adequate for any street engine, I use a bronze gear for racing.
I...
|
Forum: Model A (1928-31)
03-30-2024, 10:50 AM
|
Replies: 26
Views: 1,944
Re: Model A Marine Engine?
That is the most complete marine conversion that I have ever seen! I have no idea of its value, but the MAFFI museum may be interested in it?
|