Forum: Early V8 (1932-53)
08-17-2013, 08:30 PM
|
|
Replies: 4
Views: 2,200
Re: 32 kinkpins?
Thanks
It looks like i have nors model a king pins.
I think kinkpins are used for getting a afro.
Marv
|
|
Forum: Early V8 (1932-53)
08-16-2013, 09:39 PM
|
|
Replies: 4
Views: 2,200
32 kinkpins?
I have a new set of kingpins and dont know if they are for a 32 or a model A. Is there a way to tell? They are wards riverside part no 61-4213.
Realy dont want to buy more if these will fit.
...
|
|
Forum: Early V8 (1932-53)
07-26-2013, 08:06 AM
|
|
Replies: 6
Views: 1,139
Re: 32 pickup fuse?
Thanks Kevin
That answeres my question.I do not have a glass fuse holder so i plan on a circut breaker. I think i will start with a 25 and see how that goes.The pickup is all origional . The...
|
|
Forum: Early V8 (1932-53)
07-25-2013, 10:12 PM
|
|
Replies: 6
Views: 1,139
Re: 32 pickup fuse?
I really have no clue as to the wire size.I purchased the harness from Dick Spadero and it came from California. It has sealed beam adaptors in it now but i am planning to put stock type bulbs and...
|
|
Forum: Early V8 (1932-53)
07-25-2013, 09:46 PM
|
|
Replies: 6
Views: 1,139
32 pickup fuse?
I am installing a new wiring harness in my 32 pickup.The scematic shows a fuse between the amp guage and the light switch. I thought of just using a circut breaker but dont know what amp rating to...
|
|
Forum: Model T (1909-1927)
07-06-2013, 07:28 AM
|
|
Replies: 0
Views: 1,570
Two pedal conversion?
I have what i believe to be a 1926 coupe that i recently purchased. It has only two foot pedals? plus foot throtle, On the transmission where the brake pedal would be there is a short arm that has a...
|
|
Forum: Model T (1909-1927)
02-04-2013, 06:04 PM
|
|
Replies: 13
Views: 3,053
Re: 26 or 27 coupe?
No more pics yet. I hope to get the motor numbers and a few more pics the end of next week. It is in a garage that i don't have ready access to.
...
|
|
Forum: Model A (1928-31)
01-29-2013, 11:17 PM
|
|
Replies: 247
Views: 78,350
|
|
Forum: Model T (1909-1927)
01-27-2013, 10:06 AM
|
|
Replies: 13
Views: 3,053
|
|
Forum: Model T (1909-1927)
01-25-2013, 11:03 PM
|
|
Replies: 13
Views: 3,053
Re: 26 or 27 coupe?
Thanks for the info.I guess i will have to wait as i won't have access to it for a while.I was just hoping to get started on getting title info and need to know for sure the year.
Thanks Marv
|
|
Forum: Model T (1909-1927)
01-25-2013, 05:32 PM
|
|
Replies: 13
Views: 3,053
26 or 27 coupe?
Can anyone tell by these pics if this is a 26 or 27?As of now these are the only pics i have.
|
|
Forum: Model A (1928-31)
03-18-2012, 10:07 AM
|
|
Replies: 1
Views: 1,048
Dash board
I have a 28 pickup i recently purchased and the dash boardhas the chin like bump in the center.I thought i was told that was only roadster that used that.So do i have the wrong one?
Marv
|
|
Forum: Early V8 (1932-53)
03-12-2012, 10:45 PM
|
|
Replies: 6
Views: 1,957
Re: 32 pickup rear crossmember
Jerry
I will look at mine tomorow .Whoever was working on mine was very very welder happy and not very good at it either.Kinda looks like the pidgeons roosted above it.The ends may be savable tho....
|
|
Forum: Early V8 (1932-53)
03-11-2012, 05:32 PM
|
|
Replies: 6
Views: 1,957
Re: 32 pickup rear crossmember
Thank You
I figured out the one i was looking at will not fit.Mine has tabs for rivits through the side of the rails also.The one i found had only upper flange and lower flange rivet holes.So i...
|
|
Forum: Early V8 (1932-53)
03-10-2012, 11:42 PM
|
|
Replies: 6
Views: 1,957
|
|
Forum: Early V8 (1932-53)
03-05-2012, 06:17 PM
|
|
Replies: 3
Views: 1,012
Re: 32 pickup front crossmember
DavidG
Thanks I had it backwards i guess.I said my mount was too narrow but it is actually too wide.
My mount is 15 in and my crossmember is 12 in . I actually have two mounts that are both the...
|
|
Forum: Early V8 (1932-53)
03-05-2012, 05:47 PM
|
|
Replies: 3
Views: 1,012
32 pickup front crossmember
I have a 32 model b pickup and my front motor mount bolt spacing is too narrow for my crossmember. Is there a difference between the 4 cyl and the v-8 front crossmember? Mine is bolted in and i...
|
