Forum: Early V8 (1932-53)
10-06-2019, 01:47 PM
|
Replies: 11
Views: 2,678
|
Forum: Early V8 (1932-53)
09-16-2016, 03:04 PM
|
Replies: 20
Views: 5,037
Re: Removing pinion from 40` banjo housing
I have attached some pictures of an extremely crude tooling I put together to remove the bearing pack. I used a jackscrew and plate from a 3 leg pulley puller to act as a press. Good Luck, Norm
|
Forum: Early V8 (1932-53)
11-14-2015, 05:41 PM
|
Replies: 241
Views: 61,944
Re: Will all Veterans please arise.
Prof Henry,
Thank you very much for your attempt to recognize the Veterans on this site. As it appears, most of the Veterans served when our society had little regard for those who served. The...
|
Forum: Early V8 (1932-53)
11-11-2015, 09:55 PM
|
Replies: 241
Views: 61,944
|
Forum: Early V8 (1932-53)
08-04-2015, 02:46 PM
|
Replies: 11
Views: 3,555
|
Forum: Early V8 (1932-53)
04-24-2015, 03:38 PM
|
Replies: 11
Views: 6,419
|
Forum: Early V8 (1932-53)
04-20-2015, 04:51 PM
|
Replies: 18
Views: 3,186
|
Forum: Early V8 (1932-53)
04-10-2015, 03:10 PM
|
Replies: 27
Views: 5,835
|
Forum: Early V8 (1932-53)
03-02-2015, 08:49 AM
|
Replies: 52
Views: 9,849
|
Forum: Early V8 (1932-53)
02-11-2015, 02:20 PM
|
Replies: 19
Views: 2,518
|
Forum: Early V8 (1932-53)
01-30-2015, 03:58 PM
|
Replies: 3
Views: 1,279
Re: Tube Type Heat Gauges
I came across this the other day. I have had good results with this vendor, Third Gen Automotive. Not sure if this is the year you was looking for.
...
|
Forum: Early V8 (1932-53)
01-30-2015, 10:58 AM
|
Replies: 272
Views: 83,733
|
Forum: Early V8 (1932-53)
01-21-2015, 03:50 PM
|
Replies: 2
Views: 1,334
What size Tires
I have a 1936 Pickup with what I believe are the original size wheels, 4X16. I am not too concerned about maintaining a “Concourse” look, just a decent appearance. So here is my question:
What...
|
Forum: Early V8 (1932-53)
12-05-2014, 09:31 PM
|
Replies: 20
Views: 4,906
|
Forum: Early V8 (1932-53)
11-12-2014, 09:20 PM
|
Replies: 21
Views: 4,645
Re: My 36 Pickup
Brendan, you have a nice truck. I like the patina. Yes, I still have the mechanical brakes. I have installed Flathead Ted's floaters. I'm still needing to finish the adjustments on those. Norm
|
Forum: Early V8 (1932-53)
11-12-2014, 08:12 PM
|
Replies: 21
Views: 4,645
Re: My 36 Pickup
I finished up the rear end rebuild. The rear end is re-installed. I'm working on the truck a little at a time when the time is available.
|
Forum: Early V8 (1932-53)
10-08-2014, 10:21 PM
|
Replies: 8
Views: 4,458
Re: Setting carrier bearing preload [diff] ?
When I rebuilt my Banjo, I used Timken bearings. I did not measure these before installation assuming that they would be the exact height as original, but I would have to say they where not....
|
Forum: Early V8 (1932-53)
09-14-2014, 12:52 AM
|
Replies: 3
Views: 1,567
Re: Pinion bearings. help needed
You will need to press out the pinion gear and bearings with the outer race as a package. I made a press out of scrap metal I had.
|
Forum: Early V8 (1932-53)
09-03-2014, 09:16 PM
|
Replies: 21
Views: 4,645
My 36 Pickup
Here is my story with my 36 Pickup. This is my entry into the Early Ford hobby. Happy, Happy, Happy!!! I purchased this truck 2 years ago with the intentions of it being a driving “mild” restoration....
|
Forum: Early V8 (1932-53)
07-27-2014, 08:05 PM
|
Replies: 5
Views: 1,689
Taper Axle Treating
I know that most if not all of you recommend the taper of the axle to be clean of any material prior to installing the brake drums, but I have a question concerning the use of an Anti-Gallant...
|
Forum: Early V8 (1932-53)
07-19-2014, 12:04 PM
|
Replies: 15
Views: 2,635
Who are Your Parts Supplier?
Who do you use as your parts supplier? I am looking to compile a listing of recommended parts guys with contact information. Please include a web address is available.
Thanks,
Norm
|
Forum: Early V8 (1932-53)
06-09-2014, 04:57 PM
|
Replies: 13
Views: 1,707
Re: Hey all
Welcome to the Group. A wealth of information from these Guys is available for the asking!
Norm
|
Forum: Early V8 (1932-53)
06-08-2014, 05:14 PM
|
Replies: 5
Views: 1,630
|
Forum: Early V8 (1932-53)
05-21-2014, 03:48 PM
|
Replies: 21
Views: 12,744
|
Forum: Early V8 (1932-53)
05-20-2014, 10:12 PM
|
Replies: 2
Views: 1,450
Another Auction
A salvage business owned by Oliver Jordan in Oklahoma will have its automotive remains auctioned off. These vehicles look a bit crusty and rusty but there are some interesting ones in the mix.
...
|