Forum: Early V8 (1932-53)
04-23-2024, 10:35 PM
|
Replies: 15
Views: 667
|
Forum: Early V8 (1932-53)
12-23-2023, 10:59 PM
|
Replies: 26
Views: 1,349
|
Forum: Early V8 (1932-53)
12-05-2023, 12:14 AM
|
Replies: 12
Views: 880
Re: Mix match 8Ba & 59A pulley/distributors etc
Dale, do you happen to have any pictures or diagrams on doing the modifications that you have recommended here? Pictures speak a thousand words & make it a lot easier to understand for any of us...
|
Forum: Early V8 (1932-53)
09-13-2023, 11:37 PM
|
Replies: 37
Views: 3,168
Re: Was "Rumble Seat" published?
glennpm, thank you for taking the time to put this together & share it with us. I have it copied in print, but now have a document file for it! Bill
|
Forum: Early V8 (1932-53)
07-03-2023, 10:25 PM
|
Replies: 38
Views: 2,540
|
Forum: Early V8 (1932-53)
04-13-2023, 10:46 PM
|
Replies: 6
Views: 812
|
Forum: Early V8 (1932-53)
03-26-2023, 11:26 AM
|
Replies: 12
Views: 2,720
Re: A new car to me
I don't think that anyone will fault you for buying that! How about a full pic of the car?
|
Forum: Early V8 (1932-53)
03-09-2023, 12:05 AM
|
Replies: 18
Views: 1,939
|
Forum: Early V8 (1932-53)
03-09-2023, 12:02 AM
|
Replies: 18
Views: 1,939
Re: Bore scope?
I got one of these from Amazon a few years ago. It might be small enough to fit in the spark plug hole & turn in to the cylinder bore.
|
Forum: Early V8 (1932-53)
12-25-2022, 12:06 AM
|
Replies: 141
Views: 21,655
|
Forum: Early V8 (1932-53)
12-21-2022, 11:40 PM
|
Replies: 38
Views: 4,113
Re: Do those dipstick heaters really work?
IMHO; Be careful on using a magnetic or a silicone/stick on pan heater. Too "hot" of one can cook the oil in your pan! They are available in different wattages. Unless it is really cold out it is not...
|
Forum: Early V8 (1932-53)
11-30-2022, 11:32 PM
|
Replies: 16
Views: 2,377
Re: what piece of machinery does this fit?
It's a 90* drill adapter chuck. Chuck the threaded end/nut in any drill that is large enough to hold it & your bit in the chuck & then drill. I have a similar one somewhere around here that I don't...
|
Forum: Early V8 (1932-53)
11-12-2022, 06:26 PM
|
Replies: 12
Views: 1,853
|
Forum: Early V8 (1932-53)
11-12-2022, 06:24 PM
|
Replies: 12
Views: 1,853
Re: Ford flathead v8 starter plate
V8 Bob, I tried to attach it "opened" but can't seem to do it. There is 44 pages & the only way I could figger how to do it would be to attach every page separately. I didn't have time this am to do...
|
Forum: Early V8 (1932-53)
11-12-2022, 12:42 PM
|
Replies: 12
Views: 1,853
|
Forum: Early V8 (1932-53)
10-01-2022, 10:58 PM
|
Replies: 70
Views: 18,032
|
Forum: Early V8 (1932-53)
08-30-2022, 10:38 PM
|
Replies: 9
Views: 1,190
Re: Cast 4 1/8 pistons?
When I got my 4 1/8" pistons from Egge, they were a common in stock item. That was about 10 years ago though.
|
Forum: Early V8 (1932-53)
08-29-2022, 11:33 AM
|
Replies: 52
Views: 6,117
|
Forum: Early V8 (1932-53)
08-28-2022, 11:09 PM
|
Replies: 52
Views: 6,117
Re: Excessive crank end float.
Sorry to intrude on this, but I would like to see some final pictures showing the outcome of the repair. I am interested in case I ever run this problem. Thanks.
|
Forum: Early V8 (1932-53)
08-05-2022, 10:51 PM
|
Replies: 25
Views: 2,961
|
Forum: Early V8 (1932-53)
05-19-2022, 10:34 AM
|
Replies: 44
Views: 3,516
Re: 8ba good bellhousing, starter cover rusted out
For the tin starter bendix cover, you might look at a bearing cover cup for trailer axels. They come in several different diameters & depths, and while I do not have any sizes to reference, they look...
|
Forum: Early V8 (1932-53)
03-11-2022, 01:26 AM
|
Replies: 2,242
Views: 375,213
|
Forum: Early V8 (1932-53)
01-08-2022, 12:13 PM
|
Replies: 2,242
Views: 375,213
|
Forum: Early V8 (1932-53)
12-18-2021, 11:41 AM
|
Replies: 45
Views: 5,337
Re: Cam Tech
Frank, this last chart set came out larger & prints out good on my copier. Thank you.
|